Sucks for you guys. I went on my lunch break a bit ago and it's 72 degrees right now in Santa Monica. Sun is shining.

This is why people write songs with titles like: "I Love L.A."

 

thanks for the links guys

 

It was snowing here all day...we got a couple inches up here.it just stopped..enough to cover the roads lol

 

hey guys so i noticed that after completing my swap that there is two plugs hanging there with no where to go, located around the back of the motor, it starts up fine and there is no CEL's but what im wondering is if im going to run into any problems due to these two plugs?

 

LoL!
Umm what wiring harness did you use? Stock DA?
It's a B20 right?
Pics of said wires?

 

hmm i got some guy who offered to trade me his polished XXR 002 +0 offset 15x8 for my meshes how will that be camber and all im lowered about 2 inches on sportlines.tires are 195

also he said mesh+cash how much cash you think i should throw

http://i61.servimg.com/u/f61/14/01/41/22/pictur12.jpg
looks nice but thats 7.5 not 8inch how much difference will that make?

 

15x8 0 offset lol he should give you money plus his wheels.

Without mega camber they will look like poop, but mega camber looks like poop. In other words don't do it please

 

 

im running those same specs on my car, no camber kit, just really low with 195 45 15's. Unless you're willing to put in work on your fenders (rolling, pulling) and messing with camber i wouldnt do it. I dont think a 2" drop would be enough to tuck those

 

Duma i didn't realize that's the size you have, that size doesn't look to bad with an agressive drop A 2 inch drop will not be a good look

 

yeah 2in is deff not enough

 

i think for any kind of wheel thats low offset you should be tucking tire so it will look proper. I dont know how much camber i have but its probably alot, all natural though, so imagine if i had +40's at this height, it would be ridiculously sunk hahah

 

i like this but its 15x7.5 +0

eventually i would like to get some ground controls and roll my fenders and lower it another inch.

http://i61.servimg.com/u/f61/14/01/41/22/pictur12.jpg

duma how much are you lowered?

 

i like those rims alot more than my 002's. and to be honest 7.5's would have fit alot easier than the 8's because i wouldnt have had to flare my fenders, i dont know exactly how much im dropped but its pretty low, tucking about half the tire and its a 45 series, my chassis is about like 1" from the ground i think? last time i tried to drive over a folded up piece of cardboard to see if my car was leaking oil and it just dragged it lol

 

i want my car lower but that's not very practical

subwoofer or strutbar hmmm its tough...

 

not practical at all haha. I've been seriously debating just getting normal rims and rasing my car up to about a 1 finger gap all around, if i can get a decent trade for my sportmaxx i'd probably do it

 

yeah that's about how low i am if i had cash i would just get tires for my ssr's and put those on. but looking to trade for some cheapo wheels just to have a different look tired of the meshes but don't want to sell cause i want spares

 

I'm selling the work wheels this saturday and looking for some 16's so my car won't be as low anymore. My undercarriage is ****ed up

 

what size are your ssr's?

 

you should see the entire bottom of my car lol

 

my ssr's are 16x7 can't wait to get some cash and put them on

 

damn all this talk about negative this, positive that, I don't know **** about wheel offsets!

 

Because you haven't bought my Works yet, then you will be magically bestowed with the knowledge....

 

90 Integra RS.....slammed on skunk2

 

Wouldn't that look funny now that your fenders are pulled?

You don't need to know much. Just know that if the offset on a wheel is less than +35, the wheels were either not intended for a FF Honda, or are some of these newer off-brand wheels inspired by the low offset trend.