Honda-Tech - Honda Forum Discussion

Notices
 
Page 1 of 20
1
2
3
11
Last »
Search: Posts Made By: 4g hatch
Showing results 1 to 25 of 493
Search took 0.84 seconds.
Forum: Transmission & Drivetrain
03-06-2015, 11:45 AM
Replies: 5
Views: 949
Posted By 4g hatch

Re: Trans/diff issues.

I would replace the axle first. With open diffs if one breaks or ismt locked in the car wont move. Plus when open diffs usually go out they leave holes in the xase from the center pin breaking. When...
Forum: Transmission & Drivetrain
03-05-2015, 05:11 PM
Replies: 5
Views: 2,449
Posted By 4g hatch

Re: Mainshaft shim clearance question

Thats a very good idea. How thick should it be? I was thinking playdoe or clay like checking v2p clearances
Forum: Transmission & Drivetrain
03-05-2015, 01:05 AM
Replies: 5
Views: 2,449
Posted By 4g hatch

Mainshaft shim clearance question

Ok so I have installed hydro em1 b16 internals into a ys1 cable case. Its all together but when in neutral and u turn the mainshaft about a turn each way it spins resistance free then it gets a...
Forum: Honda CRX / EF Civic (1988 - 1991)
06-25-2014, 03:05 PM
Replies: 2
Views: 4,314
Posted By 4g hatch

dpfi to mpfi code 4 issues

Doing a obd1 b18c1 swap n my Rex. Car starts and runs but rough and wont Rev over 4. I've tried different ecu,dizzy,and jumper harness. I've ran wire from pins b10&12 straight to orange and white...
Forum: Transmission & Drivetrain
03-12-2014, 12:36 PM
Replies: 6
Views: 1,883
Posted By 4g hatch

Re: gsr internals into ys1 case??

Do u mean grind the fins down? And so the obd1 2 piece bearings will fit in the ys1 case? I didn't think they did
Forum: Transmission & Drivetrain
03-11-2014, 06:18 PM
Replies: 6
Views: 1,883
Posted By 4g hatch

Re: gsr internals into ys1 case??

Itr diff. Bearings I mean
Forum: Transmission & Drivetrain
03-11-2014, 06:17 PM
Replies: 6
Views: 1,883
Posted By 4g hatch

gsr internals into ys1 case??

I'm picking up a crx so I'm gona be switching my 94 gsr internals into a ys1 caseing. Now I'm wondering do I use it'd. Diff bearings and shims or the ls bearings with thicker shims. Any info will be...
Forum: Transmission & Drivetrain
02-21-2014, 05:59 PM
Replies: 4
Views: 623
Posted By 4g hatch

Re: 5th/reverse problem

No offense taking. I would still consider myself s novice tho I have fixed a few exploded diffs and broken gear but mistakes are possible. I try and read and learn as much as possible. Looking for...
Forum: Transmission & Drivetrain
02-21-2014, 04:35 PM
Replies: 4
Views: 623
Posted By 4g hatch

Re: 5th/reverse problem

I know its odd but I thought somebody would have experienced something similar....
Forum: Transmission & Drivetrain
02-21-2014, 11:49 AM
Replies: 4
Views: 623
Posted By 4g hatch

5th/reverse problem

Ok so my friend picked up a cable y1 tranny with a 5th gear popout. I put another used 5th gear syncro,slider,hub that was in good shape. Now we have it in the car. Drives and shifts fine. But when...
Forum: All Motor / Naturally Aspirated
04-29-2013, 01:54 PM
Replies: 49
Views: 5,503
Posted By 4g hatch

Re: H2B Prelude Rebuild

props to you....i know how you feel about having somebody else building stuff...if i cant do it then it wont get done now day....i would run steel rods also. the simpler you can keep things and still...
Forum: All Motor / Naturally Aspirated
04-29-2013, 01:42 PM
Replies: 26
Views: 5,515
Posted By 4g hatch

Re: G23 crx SI Redline

if everything is balanced and clearanced properly and you replaced the rod bolts i wouldnt worry about running the h22 redline,the ls blocks wasnt entended to rev past 7200 but with a little extra...
Forum: Drag Racing
04-22-2013, 11:28 PM
Replies: 26
Views: 30,101
Posted By 4g hatch

Re: Rear Diffuser **SHOW OFF**

i know you high hp guys see gains from using a diffuser....but im curious if mild setups the average guy may run would see any from running one?
Forum: All Motor / Naturally Aspirated
04-22-2013, 11:22 PM
Replies: 20
Views: 1,359
Posted By 4g hatch

Re: Bad rebuild on my engine...your opinions on the matter

black smoke like that means you are running waaaayyy to rich which i would guess your flooding the new rings,which may be why your loosing so much oil....fix why its running rich and then see how the...
Forum: All Motor / Naturally Aspirated
04-22-2013, 11:18 PM
Replies: 24
Views: 1,713
Posted By 4g hatch

Re: Need break-in advice.

the final hone grit on honda motors are fairly fine.its not gona wear the rings much because honda rings dont really need it. if its done right the rings should seal fine wether you baby it or beat...
Forum: All Motor / Naturally Aspirated
04-17-2013, 11:09 AM
Replies: 19
Views: 2,175
Posted By 4g hatch

Re: 12.53@106mph stock internal b20vtec

what rpm do you shift at and what oil do you run
Forum: All Motor / Naturally Aspirated
03-28-2013, 09:19 PM
Replies: 332
Views: 58,442
Posted By 4g hatch

Re: GSR build questions about clearances, power, cams

man the performer x killed the gsr manifold everywhere. thank you for sharing and being detailed :beer:
Forum: All Motor / Naturally Aspirated
03-27-2013, 11:12 PM
Replies: 7
Views: 1,206
Posted By 4g hatch

Re: another ls/v all motor build.

looks like a solid build man, but trust me find you a busted b16 tranny somewhere for cheap and grab the 4.40 fd. the ring gear will bolt on to your ls diff and all you gota do is switch the counter...
Forum: All Motor / Naturally Aspirated
03-27-2013, 11:05 PM
Replies: 45
Views: 5,953
Posted By 4g hatch

Re: Damn Toda Cams >?

i dont think lmas would cause that belt issue. only thing i could see them doing is wearing the rocker pads pre maturely, as long as it goes away when warm i wouldnt sweat it until you get all the...
Forum: Transmission & Drivetrain
03-24-2013, 06:30 PM
Replies: 6
Views: 1,469
Posted By 4g hatch

Re: Bent Gearshift Rod

if it was bent i would think you would have issues changing gears, hows the axle seals? they will leak and trail other places making it look like leaks in other places
Forum: Transmission & Drivetrain
03-23-2013, 12:26 AM
Replies: 50
Views: 12,898
Posted By 4g hatch

Post Re: Cable transmission rebuild help

They go around your input shaft. The one that has a angle sets on the isb with the anhle facing the isb and the other one sets on top or that one. Doesn't matter which way it goes. But your deff....
Forum: Hybrid / Engine Swaps
03-15-2013, 05:53 PM
Replies: 6
Views: 2,187
Posted By 4g hatch

Re: Back in the Game, B20 Question

I turn my stock ls block to 7800. Put the vtec head on tho.lol
Forum: All Motor / Naturally Aspirated
03-13-2013, 11:38 PM
Replies: 11
Views: 940
Posted By 4g hatch

Re: Need help finding out which specific B series this came off of!!

yea its a gsr and i agree with the above about being the best although some people dont like the factory intake manifold....
Forum: All Motor / Naturally Aspirated
03-13-2013, 11:33 PM
Replies: 18
Views: 5,136
Posted By 4g hatch

Re: are my valve seats worn out or ok

do you have aftermarket springs? if so the stiffer ones are hard on the valve seats
Forum: All Motor / Naturally Aspirated
03-11-2013, 11:30 PM
Replies: 13
Views: 2,902
Posted By 4g hatch

Re: built lsv what oil to run?

what alloy forging are your pistons?
Showing results 1 to 25 of 493
 
Page 1 of 20
1
2
3
11
Last »


 
Forum Jump


All times are GMT -8. The time now is 06:08 AM.