Sounds like the starter isn't working,the gear should jump forwards to grab the flywheel.
Try hitting the top of the starter when trying to start,if that don't work,buy a new starter. The teeth on the wheel are to strong,so i can't see them breaking off.

 

^^^ what he said..

 

Is it snowing in San Jo yet?? Its coming down hard over here,already a foot or so and still stacking up.

 

I'm a certified Honda Technician
Don't rattle can it. It'll only cost 150 for supplies to do it yourself with PPG supplies

Ferios are cool. They have accessories that American four doors dont. Bronze tint glass, rear wiper arm, parking pole, rear armrest. the list goes on and on.
Sounds like the soliniod has gone out. You can get it rebuild for prolly 50bucks.

 

I'm an Inside salesrep ( plus Commish $$$ ) I sell facility supplies (e.g paper towels,toilet tissue,chemicals) packaging supplies (e.g corrugated boxes,tape,stretch film..etc) and Fine paper.

 

On another note i got a new sticker for my ride : ) (By the way any news on the crew sticker ? )

 

Just got my bushings in the mail,now its a matter of "WHEN" ill be putting them on,seeing how the snow don't want to stop.

 

you guys too? i'm sick of this snow ish

 

http://www.youtube.com/watch?v=tEnhnZ-a11Y




final dyno sheet

 

would it be coo to get some skunk2 black series lug nuts for the 13 vx rims?????

or should i get some OEM ones ...

 

i was going to finish cutting the end caps for the muffler, but DOH!! I left them on my bench at the house when I cleaned the garage.

 

I found one flaw with my 91 teg today,the wipers don't lift up unless you turn them on and off fast so there's room. My wipers got stuck to the window today from the ice and snow,thank GOD i had ice melt in my washer fluid and a scraper at hand.
The snow has slowed down and the rest is melting away,i hope it all melts and never snows again.

 

get oem ones because they are an oem wheel and the oem lugs will hold it at on the whole surface versus after market where it will only hold it at 2 points




the diagram on the right is oem, the one on the left is aftermarket

 

are 92-95 lug nuts the same ??

 

i'll try to get some complete pictures of my entire car, I just cleaned the garage last night, was out there until 3 am, it's a tiny garage and I need all the space I can get. I'm going to put in my new fuel pick up tomorrow, work on the exhaust, pull my underbody fuel filter out because i need to modify the bracket, figure out a place under there for a fuel pump, and i'm going to try to work on some wiring, I'm also going to bring my new dash out there to work on it, on top of that I need to find oil leaks on the Lincoln, and pull the alternator out of the 98 to test fit into the 86

 

inventing food,

need one 6 oz box of instant stuffin'
one 8 oz can of sweet peas
one 14 oz can of white potatoes, small squares
one 14 oz can of carrots
a few green onions cut up
1 12 oz can of chicken chunks or fresh chicken cut up
3 cups of cream of mushroom soup
1 cup of Parmesan cheese
some Italian seasoning
prepare stuffing, set aside
combine other ingredients and cover with stuffin' in oven safe dish, bake at 350 for 30 minutes
enjoy

 

I'm working on a b18 swap and I am stuck on the wireing does anyone have an easy way I can wire it without running the entire harness. Just the one on the motor oh it an 88 civic anyhelp plz

 

You would need to convert the OE harness if its the dull injectors,its not hard to do,just tapping more injectors in then running it.
You can buy a swapping book that will show you how its done for like 5 bucks from summit racing. The book has just about every DIY swapping and shows you how to make your own harness.

 

im a mechanic in fresno for del rey tire and retreading..

 

whats up bnb its been hard since thursday doctor called and said my son has an infection in his blood so weve been there so havent had time to post lately, hope its just a contaminated blood culture tough.

 

yea they are the same bro. check on the gauge today he hasnt found a used one for the circuit sheet yet but dont want to buy a used one cuz they run around 80 to 90 for the clusters hes tryin to just take it of and five finger discount the sheet but i told him if the gauges are good ill just buy it for the right price....

 

did i say something wrong in here? if I did it certainly wasn't intended, i just get the feeling I pissed everyone off for some reason

 

dam bro im sorry to hear that i hope he gets better and i wish the best for him ..

 

its alright dude .. if he cant find the sheet then.... its cool my car wnt be running for another 2-3 weeeks sso im not stressin it .

 

not me