Honda-Tech - Honda Forum Discussion

 
Page 1 of 4
1
2
3
Last »
Search: Posts Made By: balliso911
Showing results 1 to 25 of 78
Search took 0.29 seconds.
Forum: Honda Prelude
08-14-2013, 07:22 AM
Replies: 4
Views: 710
Posted By balliso911

Re: 93 SI rough first start

No codes and new battery within the year
Forum: Honda Prelude
08-12-2013, 02:39 PM
Replies: 4
Views: 710
Posted By balliso911

93 SI rough first start

Trying to troubleshoot my starting issue. It's a 93 SI VTEC with 285k, no mods, it has a h22a4 swapped but I was having same issues when the h22 was in there so I don't think the motor is to blame. ...
Forum: Honda Prelude
11-12-2012, 11:50 AM
Replies: 3
Views: 1,715
Posted By balliso911

Re: H22a4 Swap

OP, i swapped an A4 into my 93 but i kept it OBDI. if you have any questions on that hit me up i will try and help you.
Forum: Honda Prelude
11-12-2012, 11:42 AM
Replies: 2
Views: 1,444
Posted By balliso911

Re: 94 prelude idle and running problem

if your idle speed is eratic when warming up the culprit is most likely the FITV. Remove it and clean it real good, replace O rings and reinstall. You will most likely have air pockets in your...
Forum: Honda Prelude
08-21-2012, 06:17 AM
Replies: 39
Views: 23,810
Posted By balliso911

Re: dyno numbers for a stock h22a4

so, i did a comp test and its just under 180 for each cylinder.

my tran fluid was a little high so i drained some out.

i changed the fuel filter, checked the plugs, rotor, and cap.

i then...
Forum: Honda Prelude
08-05-2012, 12:41 PM
Replies: 39
Views: 23,810
Posted By balliso911

Re: dyno numbers for a stock h22a4

so if i understand u right, those numbers mean im running rich which is "average" on stock ecu and 13:1 is more consitent with a tuned ecu? im running on a p13, BTW, didnt want to leave any info out...
Forum: Honda Prelude
08-05-2012, 08:32 AM
Replies: 39
Views: 23,810
Posted By balliso911

Re: dyno numbers for a stock h22a4

i did state it was running lean in the original post

and yes your right, a graph would help alot, all i have is a hard copy and the picture i took, which i was going to upload, is unreadable.
...
Forum: Honda Prelude
08-04-2012, 02:27 PM
Replies: 39
Views: 23,810
Posted By balliso911

Re: dyno numbers for a stock h22a4

hey thanks q16racer, i didnt know it would be an issue asking a "prelude forum" how much HP to the wheels a stock h22a4 puts down or if running lean on a dyno run could be causing the issue im...
Forum: Honda Prelude
08-02-2012, 07:09 AM
Replies: 39
Views: 23,810
Posted By balliso911

Re: dyno numbers for a stock h22a4

good point, i was not aware of that. I thought that was the materal the sleeve was made out of. The guy at the machine shop told me the walls were scoured to bad to be honed, recommended new sleeves....
Forum: Honda Prelude
08-02-2012, 06:33 AM
Replies: 39
Views: 23,810
Posted By balliso911

Re: dyno numbers for a stock h22a4

stock tires

yea ima check compression this weekend, i work two jobs during the week so i have little time for turning wrenches.

good suggestion on checking the intake - exhaust because there is...
Forum: Honda Prelude
07-31-2012, 05:48 PM
Replies: 39
Views: 23,810
Posted By balliso911

Re: dyno numbers for a stock h22a4

yup, i guess every build no matter how complex has "gremlins" to work out, and find. Finding them seems to be the hard part.

im just gonna have to put the keys on the rack til the weekend when i...
Forum: Honda Prelude
07-31-2012, 05:27 PM
Replies: 39
Views: 23,810
Posted By balliso911

Re: dyno numbers for a stock h22a4

it is stock, i had the stock FRM sleeves put in, new rings on the pistons. the valve job was just a 3 angle on stock valves, i didnt upgrade them. I had the long block out i figured i would go...
Forum: Honda Prelude
07-31-2012, 05:22 PM
Replies: 39
Views: 23,810
Posted By balliso911

Re: dyno numbers for a stock h22a4

p13

not tunned

timing checked

the injectors are from the original motor (h22) which i never had issues with so i never did anything to them.

the plugs are new and the cap n rotor are...
Forum: Honda Prelude
07-31-2012, 03:05 PM
Replies: 39
Views: 23,810
Posted By balliso911

Re: dyno numbers for a stock h22a4

yea it does, its pissing me off too. Just from some internet search the b18 are putting around 140 to the wheels, stock.

there was a thread on prelude online from like 03, the guy had a 01 stock...
Forum: Honda Prelude
07-31-2012, 02:28 PM
Replies: 39
Views: 23,810
Posted By balliso911

Re: dyno numbers for a stock h22a4

its a 5 speed.


ive tried research, but most info found is ppl posting dyno's after their car has been modded.

i just find it hard to believe that almost a third of the vehicles HP get soaked...
Forum: Honda Prelude
07-31-2012, 12:13 PM
Replies: 39
Views: 23,810
Posted By balliso911

Re: dyno numbers for a stock h22a4

i didnt, i assumed compression would be where it should be considering i just had a sh*t load of work done. sleeves, rings, valve job, etc.

what about the numbers? is that where it should be?
Forum: Honda Prelude
07-31-2012, 10:59 AM
Replies: 39
Views: 23,810
Posted By balliso911

dyno numbers for a stock h22a4

did an h22a4 swap into my 93 prelude a few months ago. It felt like it wasnt running really strong, felt some hesitation throughout the RPM range.

took it to the shop and had the car on dyno for...
Forum: Honda Prelude
06-17-2012, 08:50 AM
Replies: 3
Views: 1,219
Posted By balliso911

Re: Fresh up my prelude, bushing kit

Yea that's where I'm getting the kit and I got 273k on the suspension so I'm sure they r in there pretty good.

I wanted to DIY and planned on dedicating a full day to the job, just wondering...
Forum: Honda Prelude
06-17-2012, 07:15 AM
Replies: 3
Views: 1,219
Posted By balliso911

Fresh up my prelude, bushing kit

Im looking to do some updating on some of the old parts on my prelude. I want to install a new carpet and master bushing kit, smooth the ride out a little bit.

My question being that I've never...
Forum: Honda Prelude
06-11-2012, 09:19 AM
Replies: 53
Views: 24,120
Posted By balliso911

Re: FOR SALE ONLY ::.. NO TRIAL USERS, NO COMMENTS, PICTURES REQUIRED - May-June 201

Posted is the engine harness from a 99 prelude base and stock injectors and rail from same vehicle. Buyers pay shipping and fees. I also have other misc engine parts from a4 and a1. HMU i may it.
...
Forum: Honda Prelude
06-03-2012, 05:10 AM
Replies: 1
Views: 779
Posted By balliso911

EGR question

i have a vacuum leak and i suspect the problem is coming from where the vacuum hoses meet with the EGR solenoid valve and EGR vacuum control valve. I have a 93 vtec but am currently using the IM from...
Forum: Honda Prelude
05-11-2012, 02:07 PM
Replies: 5
Views: 4,643
Posted By balliso911

Re: Crank Position sensor

hey im pretty sure that the 96 OBDI does not have the crank sensor mounted in the front by the timing housing. i have a 93 which does not have one there.
I know this doesnt solve your problem but...
Forum: Honda Prelude
05-11-2012, 01:55 PM
Replies: 4
Views: 1,016
Posted By balliso911

Re: Wiring harness??

i actually just finished a similiar swap today. i put a a4 into my 93 which was an a1.
1. you can remove the crank sensor because the a1 harness does not have a connector for that.
2. you will...
Forum: Honda Prelude
05-04-2012, 12:51 PM
Replies: 1
Views: 494
Posted By balliso911

IM question, need help

i have almost completed my swap. its a a4 into a 93 vtec which was an h22a1. i am using the IM from the a4 which is where i am running into some issues. there are three hoses that come off what i...
Forum: Honda Prelude
04-10-2012, 06:02 AM
Replies: 16
Views: 1,515
Posted By balliso911

Re: Engine swap question

also, instead of starting a new thread, one more question. anybody have advice on a good break in process for the new engine? pretty much everything on the long block is new or machined. thanks again
Showing results 1 to 25 of 78
 
Page 1 of 4
1
2
3
Last »


 
Forum Jump


All times are GMT -8. The time now is 01:25 AM.