jdmland

everytime i let off the clutch i can hear a klunk,or when i brake hard or shift.
not the cv kind of klunk, nothing while turning so i rulled out the axel.
So i jack the car up, notice the tierod end boot is ripped to ****, but not the axle.
So i grabbed the driverside wheel and i seem to wiggle it a little,(same noise while all above stuff happens) passenger side seems nice and tight no wiggle, just the drivers, so i'm leaning towards the wheel bearing, but before i go and replace it, could possibly the tierod end be the prob?since i noticed the boot was all ripped to ****? i don't thing that would make the wheel wiggle a little when i pull on it, just wanna make sure.

wastedyouth2542

probably the wheel bearing but not sure, im leaning toward wheel bearing tho good luck

Jimmy

iTrader: (5)

Wheel bearing..

Also replace the tie rod.

steveo135

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Jimmy &raquo;</TD></TR><TR><TD CLASS="quote">Wheel bearing..

Also replace the tie rod.</TD></TR></TABLE>

x2

SuckMyDOHC

iTrader: (1)

x3

butand50

ahh fork it.... x4

jdmland

Found the problem, upper ball joint, when push down on the upper control arm i hear a clunk, plus it seems loose.
Now replacement balljoints are insane prices, does anybody know of a cheap place to pic one up at?, possibly get a universal one?
autozone dosne't list just the ball joint, i heard napa has universal ones that will work ,anybody?
I'm not about to buy the complete upper control arm.

Jimmy

iTrader: (5)

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by jdmland &raquo;</TD></TR><TR><TD CLASS="quote">Found the problem, upper ball joint, when push down on the upper control arm i hear a clunk, plus it seems loose.
Now replacement balljoints are insane prices, does anybody know of a cheap place to pic one up at?, possibly get a universal one?
autozone dosne't list just the ball joint, i heard napa has universal ones that will work ,anybody?
I'm not about to buy the complete upper control arm.
</TD></TR></TABLE>

If you really think that is the issue.. you can buy just the balljoint from acura.. or where ever..

but i wouldn't recommend you beating it out.. Take the upper control arm off and take is to a shop and have them press it.. or press it yourself if you have access..

Dogginator

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Jimmy &raquo;</TD></TR><TR><TD CLASS="quote">

If you really think that is the issue.. you can buy just the balljoint from acura.. or where ever..

but i wouldn't recommend you beating it out.. Take the upper control arm off and take is to a shop and have them press it.. or press it yourself if you have access..

</TD></TR></TABLE>

Acura doesn't sell upper balljoints, just lower. You have to buy the whole upper control arm from them.

Jimmy

iTrader: (5)

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Dogginator &raquo;</TD></TR><TR><TD CLASS="quote">

Acura doesn't sell upper balljoints, just lower. You have to buy the whole upper control arm from them.</TD></TR></TABLE>

Your right..

http://www.acuraoemparts.com/d...ch=no

That sucks.

To the OP.. Call up the local parts stores.. or just buy the whole upper control arm.. Now would be a good time to get a good omnipower or skunk 2 front camber kit

jdmland

this should work
http://www.partsamerica.com/pr...Set=A