What rpm do you turbo guys lanch hear? Please let me know.
Thread Starter
Joined: Jun 2002
Posts: 194
Likes: 0
From: yuba ciyty, ca, USA
What rpm do you turbo guys lanch hear? Please let me know.
Raced a stock gsr, yesterday and he got a huge jump on me because i launched at 3500, next time i am launching at 4500-5000, any ways let me know thanks. Oh yeah I am running 7 psi with the afc hack, but my turbo not making any boost tht might be it, too.
[Modified by therumblingteg, 2:08 PM 9/3/2002]
[Modified by therumblingteg, 2:08 PM 9/3/2002]
Smarter than you
iTrader: (1)
Joined: Apr 2001
Posts: 8,240
Likes: 2
From: Third Coast, united states
Re: What rpm do you turbo guys lanch hear? Please let me know. (Matthew)
haha 
for the sake of this thread I luanch my car at 4400 rpm on heated up drag radials.
for the sake of this thread I luanch my car at 4400 rpm on heated up drag radials.
Trending Topics
Member
Joined: Feb 2002
Posts: 1,810
Likes: 0
From: woods cross, ut, usa
Re: What rpm do you turbo guys lanch hear? Please let me know. (therumblingteg)
when I first launched on street tires(kumho) I dropped it a 5000 and spun tires all through 1st and 2cnd. If I were you on street tires I would launch around the 2500-3500 range and feather the clutch..works pretty well. OF course if your turbo isnt spoolin then it wont do you much good..
[Modified by tygsr, 5:08 PM 9/3/2002]
[Modified by tygsr, 5:08 PM 9/3/2002]
Joined: Jun 2002
Posts: 1,086
Likes: 0
From: FT. Lauderdale, Florida, USA
Re: What rpm do you turbo guys lanch hear? Please let me know. (therumblingteg)
did i read that first post right? your running 7psi and launched at 3500rpm and a STOCK gsr pulled on you? i hope you where spinning then thru 1st or the gsr launched at like 7000rpm with some slicks cuz stock gsr really dont pull hard thru 1st at all......
New User
Joined: Mar 2001
Posts: 12,296
Likes: 0
Re: What rpm do you turbo guys lanch hear? Please let me know. (therumblingteg)
7000-7200rpms off the 2 step building approx 5 psi off the line. MT 24.5x8x13 slicks on Lensos, best 60ft is a 1.67 only once, usually low 1.7s.
21 lbs on a 
civic si!!!!!!! how... 
Thread Starter
Joined: Jun 2002
Posts: 194
Likes: 0
From: yuba ciyty, ca, USA
Re: What rpm do you turbo guys lanch hear? Please let me know. (VaporTrail)
i had leaks lots of them, and i fixed them. I was running 1 psi yesterday. But I raced him again, launched at 4500, and took him out at 7 psi, but not by how much i wanted too? How much should i be pulling him by. I had him in first second thinrd, and fourth, he just stoped is third cause i pulled him bad. I still lanch at 4500 on the street. OH YEAH ONE MORE THING I CHUTCH IS SHOT I MEAN IT IS SHOT.
Honda-Tech Member
Joined: Jun 2001
Posts: 1,906
Likes: 0
From: NC, USA
Re: What rpm do you turbo guys lanch hear? Please let me know. (tygsr)
when I first launched on street tires(kumho) I dropped it a 5000 and spun tires all through 1st and 2cnd. If I were you on street tires I would launch around the 2500-3500 range and feather the clutch..works pretty well. OF course if your turbo isnt spoolin then it wont do you much good..
Junior Member
Joined: Dec 2001
Posts: 404
Likes: 0
From: enola, PA, USA
Re: What rpm do you turbo guys lanch hear? Please let me know. (therumblingteg)
herm...on the street i'm launching at around 3500 on street tires(kumho) and i still get a bit of wheel spin, ek w/b18c1,...and u wanna launch at 4500-5000 on street tires with 7psi?
Thread
Thread Starter
Forum
Replies
Last Post
