Q's about mini-me swap that I haven't found in searches....
#1
Member
Thread Starter
Join Date: Dec 2003
Location: Pittsburgh, PA, USA
Posts: 1,226
Likes: 0
Received 0 Likes
on
0 Posts
Q's about mini-me swap that I haven't found in searches....
Most of the info that I've found on Mini-me's has been about different makes and models so I wanted to make sure I wasn't too far off. I have a 96 Sol (that is OBDII ) the motor in it now is the factory D16Y7 non-vtec , I have also acquired a few freebies from friends and mechanics, and want to start putting them togethor...
I have 2 intake manifolds and throttle bodies one from a 95 civic ex, and the other from a 93 ex (the two look almost identical)
A D16Z6, missing only the distributor (odd noise in bottom half so whole motor was replaced I inherited what was left)
An OBD1 p28 ECU, with a "spoon style" chip (not yet installed
which dizzy would I use, can I use the one on my D16Y7? and am I going to need any different sensors? or will they just need rewired
thanxs in adavance for any help...
I have 2 intake manifolds and throttle bodies one from a 95 civic ex, and the other from a 93 ex (the two look almost identical)
A D16Z6, missing only the distributor (odd noise in bottom half so whole motor was replaced I inherited what was left)
An OBD1 p28 ECU, with a "spoon style" chip (not yet installed
which dizzy would I use, can I use the one on my D16Y7? and am I going to need any different sensors? or will they just need rewired
thanxs in adavance for any help...
#2
Member
Thread Starter
Join Date: Dec 2003
Location: Pittsburgh, PA, USA
Posts: 1,226
Likes: 0
Received 0 Likes
on
0 Posts
Re: Q's about mini-me swap that I haven't found in searches.... (foz)
Is my question that nooby, or does noone know?
I already have an AEM CAI, DC Sports 4-2-1 header, custom piping from header to Skunk2 Universal muffler... I am happy with the car and the amount of power, mainly 'cuz of how well it handles...(all skunk2 tower bars, lower tie, coil-overs w/tokico struts) but would like to give it a little more if I could get the car to produce around 150hp I would be completely satisfied, and I am hoping that these parts will help me acquire that but want to make sure I have all that I need before I start tearing it apart
I have found very thorough parts lists, and how-to's through this site and many users here, but haven't seen one with this combo
Is it any different?
I already have an AEM CAI, DC Sports 4-2-1 header, custom piping from header to Skunk2 Universal muffler... I am happy with the car and the amount of power, mainly 'cuz of how well it handles...(all skunk2 tower bars, lower tie, coil-overs w/tokico struts) but would like to give it a little more if I could get the car to produce around 150hp I would be completely satisfied, and I am hoping that these parts will help me acquire that but want to make sure I have all that I need before I start tearing it apart
I have found very thorough parts lists, and how-to's through this site and many users here, but haven't seen one with this combo
Is it any different?
#4
Member
Thread Starter
Join Date: Dec 2003
Location: Pittsburgh, PA, USA
Posts: 1,226
Likes: 0
Received 0 Likes
on
0 Posts
Re: Q's about mini-me swap that I haven't found in searches.... (BauleyCivic)
so than I should use one for a z6, the plugs will be different right?
can I just rewire them to the existing dist wires since the ecu will be obdi?
can I just rewire them to the existing dist wires since the ecu will be obdi?
Thread
Thread Starter
Forum
Replies
Last Post
beninitEk96
Honda Civic / Del Sol (1992 - 2000)
15
08-19-2010 12:49 PM
beninitEk96
Honda Civic / Del Sol (1992 - 2000)
4
12-03-2008 04:01 AM