Let's hear about your turbo setup's.
#1
Honda-Tech Member
Thread Starter
Join Date: May 2002
Location: California
Posts: 3,047
Likes: 0
Received 0 Likes
on
0 Posts
Let's hear about your turbo setup's.
Please list the vehicle it is equipped on including motor (so we know all those hybrid turbo users out there), the boost level you are running and if you have dyno results please post your wheel hp and tq numbers. Also feel free to brag your timeslips (please indicate if on street tires, street "slicks" or drag only slicks).
Since their are so many variables in most other turbo kits or custom setups, please add details. One day you might look back on someone elses setup for insight on what to do next.
Thanks to CSi for this idea.
#2
Honda-Tech Member
Join Date: Aug 2001
Location: Bangkok, Thailand, Thailand
Posts: 4,096
Likes: 0
Received 1 Like
on
1 Post
Re: Let's hear about your turbo setup's. (RyanAutry)
Well, its not up and running yet, but it should be complete by the end of this week/early next week..
<u>RHD Honda Integra VTi-R</u>
B20B shortblock, B18C head, B18C tranny
F-Max turbokit (for B18C)
Turbonetics T3/T4 hybrid turbo
Tial wastegate
GReddy Type-R blowoff valve
GReddy manual boost controller
JDM B18C-R spec98 cams
Ferrea Stainless Steel Valves
Ferrea Bronze Valve Guides
Crower Springs
Crower Retainers
Stock B20B crankshaft
Stock B20B connecting rods (sitting in room: Eagle Forged connecting rods for B18C)
Stock B20B pistons (sitting in room: JE 81.5mm 9:1 pistons)
ARP studs
RC 550CC injectors
AEM Fuel Rail
AEM TruTime cam gears
Unorthodox pulleys
Skunk2 intake manifold
Modified D16Y8 fuel pressure regulator
Nology external coil
MSD distributor cap
Accel wires
SCE head gasket
Vitek 500HP driveshaft & axle
Clutchmasters Stage 4 clutch
Quaife 50% Limited Slip Differential
Mitsubishi Lancer Evolution V intercooler
HKS 2JZ-GTE oil cooler
Link Engine Management / IntegraLink ECU
That's about it.. no numbers/figures yet, but with the old B18C setup (with the JE/Eagle stuff) I raced with my friend's Mitsubishi Evo 7 from standstill, and overtook him in 3rd gear (at 0.8 bar of boost).
i'll edit this post as I progress with my project
[Modified by turbopanda, 2:48 AM 12/5/2002]
<u>RHD Honda Integra VTi-R</u>
B20B shortblock, B18C head, B18C tranny
F-Max turbokit (for B18C)
Turbonetics T3/T4 hybrid turbo
Tial wastegate
GReddy Type-R blowoff valve
GReddy manual boost controller
JDM B18C-R spec98 cams
Ferrea Stainless Steel Valves
Ferrea Bronze Valve Guides
Crower Springs
Crower Retainers
Stock B20B crankshaft
Stock B20B connecting rods (sitting in room: Eagle Forged connecting rods for B18C)
Stock B20B pistons (sitting in room: JE 81.5mm 9:1 pistons)
ARP studs
RC 550CC injectors
AEM Fuel Rail
AEM TruTime cam gears
Unorthodox pulleys
Skunk2 intake manifold
Modified D16Y8 fuel pressure regulator
Nology external coil
MSD distributor cap
Accel wires
SCE head gasket
Vitek 500HP driveshaft & axle
Clutchmasters Stage 4 clutch
Quaife 50% Limited Slip Differential
Mitsubishi Lancer Evolution V intercooler
HKS 2JZ-GTE oil cooler
Link Engine Management / IntegraLink ECU
That's about it.. no numbers/figures yet, but with the old B18C setup (with the JE/Eagle stuff) I raced with my friend's Mitsubishi Evo 7 from standstill, and overtook him in 3rd gear (at 0.8 bar of boost).
i'll edit this post as I progress with my project
[Modified by turbopanda, 2:48 AM 12/5/2002]
#3
Re: Let's hear about your turbo setup's. (turbopanda)
Would you also like us to add our addresses and exactly where we store out turbo cars?
Honestly this is a inocent question....but risky to answer
****anyone (anywhere) can read this thread's content****
[Modified by SLPR, 11:02 AM 12/4/2002]
Honestly this is a inocent question....but risky to answer
****anyone (anywhere) can read this thread's content****
[Modified by SLPR, 11:02 AM 12/4/2002]
#6
Honda-Tech Member
Join Date: Oct 2002
Location: Phoenix, AZ., USA
Posts: 2,456
Likes: 0
Received 0 Likes
on
0 Posts
Re: Let's hear about your turbo setup's. (turbopanda)
Here's mine, no fuel mods yet but they should be done next month(255 walbro f.p., 310 rc injectors and b&m f.p.r.).
#7
Honda-Tech Member
Join Date: Apr 2002
Location: bay area, ca, usa
Posts: 300
Likes: 0
Received 0 Likes
on
0 Posts
Re: Let's hear about your turbo setup's. (turbopanda)
i think i saw your car in auto mobil racing cars magazine(thai magazine). i am thai too. i will ship my car to thailand next year(fully built integra but 4door). how many hp do you have?
Trending Topics
#9
Re: Let's hear about your turbo setup's. (gsrt)
93 Si
b18c1
9:5:1 Srp
Eagle rods
Inline Pro Mani
60-1 3" inlet
hondata 2b
550's
3" DP
stock sleeves and blockguard
334/239 @ 15psi
Last dyno
15 psi everyday and have ran as high as 19psi at the track
b18c1
9:5:1 Srp
Eagle rods
Inline Pro Mani
60-1 3" inlet
hondata 2b
550's
3" DP
stock sleeves and blockguard
334/239 @ 15psi
Last dyno
15 psi everyday and have ran as high as 19psi at the track
#10
Smarter than you
iTrader: (1)
Join Date: Apr 2001
Location: Third Coast, united states
Posts: 8,240
Likes: 0
Received 2 Likes
on
2 Posts
Re: Let's hear about your turbo setup's. (RyanAutry)
95 Integra LS
stock LS motor
stock LS tranny
ACT hd/ss clutch
revhard kit- t3/t04e 57trim
hondata- rc 550-walbro intank(tuned by john gadd(VAPORTRAIL) at secret services)
thermal exhaust
274/237 @ 12psi
13.0 @ 110 -12psi on bfg drag radials
simple yet effective.
stock LS motor
stock LS tranny
ACT hd/ss clutch
revhard kit- t3/t04e 57trim
hondata- rc 550-walbro intank(tuned by john gadd(VAPORTRAIL) at secret services)
thermal exhaust
274/237 @ 12psi
13.0 @ 110 -12psi on bfg drag radials
simple yet effective.
#11
Honda-Tech Member
Join Date: Aug 2001
Location: manakin sabot, va, us
Posts: 4,083
Likes: 0
Received 0 Likes
on
0 Posts
Re: Let's hear about your turbo setup's. (DIRep972)
94 honda accord
engine
D-stroked
h23a1 engine
nascar sleaves
10.2:1 arias bored 40over pistons
eagle rods for h22a
h22a crank
h22a oil pump
h23 head
5 angle valve job
new valve guides with seals
P&P head
1998 f22 tranny
Fuel
buying now
hondata
720cc's
3 bar map
holley or bbk 255lph fuel pump
centerforce clucth
turbo kit
Modified drag manifold
garrett t3/t04e 60trim .63 turbine
modified drag teg fmic
apexi BOV
XS manual boost controller
electronics
MSD 6T
MSD Blaster Coil
accel 8mm wires
NGK plugs
Autometer Boost
A/F gauge
Greddy turbo timer
MSD soft touch rev control
msd 2 step
exhaust
3" Custom exhaust
3" down pipe
wheels
slicks 22-8-15 M/T
street
225-35-19
koing 19/8 rims
with tenzo springs
no #'s or track times yet
engine
D-stroked
h23a1 engine
nascar sleaves
10.2:1 arias bored 40over pistons
eagle rods for h22a
h22a crank
h22a oil pump
h23 head
5 angle valve job
new valve guides with seals
P&P head
1998 f22 tranny
Fuel
buying now
hondata
720cc's
3 bar map
holley or bbk 255lph fuel pump
centerforce clucth
turbo kit
Modified drag manifold
garrett t3/t04e 60trim .63 turbine
modified drag teg fmic
apexi BOV
XS manual boost controller
electronics
MSD 6T
MSD Blaster Coil
accel 8mm wires
NGK plugs
Autometer Boost
A/F gauge
Greddy turbo timer
MSD soft touch rev control
msd 2 step
exhaust
3" Custom exhaust
3" down pipe
wheels
slicks 22-8-15 M/T
street
225-35-19
koing 19/8 rims
with tenzo springs
no #'s or track times yet
#12
Honda-Tech Member
Join Date: Dec 2001
Location: The Swamp, FL
Posts: 7,139
Likes: 0
Received 0 Likes
on
0 Posts
Re: Let's hear about your turbo setup's. (DLB1994)
1998 Integra GS
_______________
Current Mods:
Skunk2 IM
Greddy Exhaust
Thats it.
Best 1/4 to date - 13.7
_______________
Current Mods:
Skunk2 IM
Greddy Exhaust
Thats it.
Best 1/4 to date - 13.7
#13
Honda-Tech Member
Join Date: Aug 2001
Location: Bangkok, Thailand, Thailand
Posts: 4,096
Likes: 0
Received 1 Like
on
1 Post
Re: Let's hear about your turbo setup's. (gsrt)
i think i saw your car in auto mobil racing cars magazine(thai magazine). i am thai too. i will ship my car to thailand next year(fully built integra but 4door). how many hp do you have?
automobil racing cars magazine is available in US too?!!?!
my car hasn't been on the dyno yet, so I can't tell you how many HP it has.
do you know meng header?
you'll be bringing your car to thailand?! wow.. i can't wait to see it you will be the only 4 door integra in thailand!
#14
Honda-Tech Member
Thread Starter
Join Date: May 2002
Location: California
Posts: 3,047
Likes: 0
Received 0 Likes
on
0 Posts
Re: Let's hear about your turbo setup's. (SLPR)
Would you also like us to add our addresses and exactly where we store out turbo cars?
Honestly this is a inocent question....but risky to answer
****anyone (anywhere) can read this thread's content****
Honestly this is a inocent question....but risky to answer
****anyone (anywhere) can read this thread's content****
Now, how exactly would "someone" know where you lived and what your car looks like when your listing your turbo setup???
#15
Honda-Tech Member
Re: Let's hear about your turbo setup's. (RyanAutry)
drag 3 manifold
precision turbo t3t4 .60/.63ar 50 trim stage 3wheel, ported housings
starion fmic
celica all trac injectors (440cc)
supra tt fuel pump
apexi vafc
blitz bov
tial 35mm wastegate
taylor plug wires
msd6btm
accel coil
greddy 2mm head gasket
arp head studs
2.5 downpipe (not even complete this one jsut basically points down)
fjo wideband o2
act 6puc clutch coming soon
#16
Honda-Tech Member
Join Date: Feb 2002
Location: 648 at 8,500
Posts: 2,937
Likes: 0
Received 0 Likes
on
0 Posts
Re: Let's hear about your turbo setup's. (turbopanda)
<u>RHD Honda Integra VTi-R</u>
Nice set-up!
Hey I'm gonna be in Thailand for all of May 2003 and was wondering how are the prices compared to here and if you could maybe PM me a couple of places that sell performance parts for our cars. Meng Header ect.
Thanks,
Ryan
[Modified by Blickstick, 10:13 PM 12/4/2002]
#17
Honda-Tech Member
Re: Let's hear about your turbo setup's. (Blickstick)
88 Civic HB
ZC Tranny/Si Longblock
Greddy TD04H
Trust FMIC
DSM BOV
1g DSM Injectors
SMC
ACT 6 Puck/Fidanza 9lb/eXtreme PP
MSD 6A w/ cap/coil
more crap...too lazy to type any more
jB
ZC Tranny/Si Longblock
Greddy TD04H
Trust FMIC
DSM BOV
1g DSM Injectors
SMC
ACT 6 Puck/Fidanza 9lb/eXtreme PP
MSD 6A w/ cap/coil
more crap...too lazy to type any more
jB
#18
Re: Let's hear about your turbo setup's. (RyanAutry)
1988 honda crx hybrid
18g turbo 18 psi
hondata stage 4 w/ boost
crower cams
crower rods
crower stainless steel valves
5 angle valve job
tit ret
dual springs
srp 9:1 copm piston w 3.209 bore stock is 3.189
str block guard
act 6 puck clutch
degeed cams
deburred head
hondata intake gasket
3" thermal turbo exhaust
2.5 down pipe w/ 2.5 cat
passed emmisions in ct on pump gas in ct
333fwhp at 7725 rpm
245 torque at 5450 rpm
redline 8000rpm
tial 40mm wastegate w/1 bar spring
apex boost controller
stock intake
greddy oil cooler
greddy intercooler front mount
small 2" i/c piping
550cc injectors running at 85% at 8000rpm fuel pressure at 50psi
255lph fuel pump warlboro
balanced crank
cm lightened flywheel
LS integra tranny
b16a1 1989 motor
pr3 ecu
greddy bov
autolite plugs
adj. cam gears
fpr aem
srt fuel rail
light crank pulley
18g turbo 18 psi
hondata stage 4 w/ boost
crower cams
crower rods
crower stainless steel valves
5 angle valve job
tit ret
dual springs
srp 9:1 copm piston w 3.209 bore stock is 3.189
str block guard
act 6 puck clutch
degeed cams
deburred head
hondata intake gasket
3" thermal turbo exhaust
2.5 down pipe w/ 2.5 cat
passed emmisions in ct on pump gas in ct
333fwhp at 7725 rpm
245 torque at 5450 rpm
redline 8000rpm
tial 40mm wastegate w/1 bar spring
apex boost controller
stock intake
greddy oil cooler
greddy intercooler front mount
small 2" i/c piping
550cc injectors running at 85% at 8000rpm fuel pressure at 50psi
255lph fuel pump warlboro
balanced crank
cm lightened flywheel
LS integra tranny
b16a1 1989 motor
pr3 ecu
greddy bov
autolite plugs
adj. cam gears
fpr aem
srt fuel rail
light crank pulley
Thread
Thread Starter
Forum
Replies
Last Post
b18c4door
Forced Induction
14
12-10-2003 05:11 PM