Honda-Tech - Honda Forum Discussion

 
Page 1 of 10
1
2
3
Last »
Search: Posts Made By: n/a2boost
Showing results 1 to 25 of 233
Search took 0.38 seconds.
Forum: Tech / Misc
12-29-2014, 03:48 PM
Replies: 3
Views: 1,176
Posted By n/a2boost

Re: Help identifying plugs.

What year is the chassis? Pics of the smaller harness. Guessing that there's a light gray 20 position plug that plugs into the rywire engine harness then either the same light gray plug or even the...
Forum: Tech / Misc
12-14-2014, 03:07 PM
Replies: 2
Views: 745
Posted By n/a2boost

Re: S2K Dash Cluster

K-tuned s2000 dash converter is what you need to correct the fuel,speed and water temp.
Forum: Tech / Misc
10-23-2014, 12:09 PM
Replies: 20
Views: 3,266
Posted By n/a2boost

Re: OBD1 Custom Wiring harness for Custom car

The computer does not turn the radiator fan on. The fan switch turns on the fan. A12 is so the ecu knows the fan is on and can adjust things.

You don't need the starter signal switch b9.

The...
Forum: Tech / Misc
10-22-2014, 03:47 PM
Replies: 10
Views: 2,024
Posted By n/a2boost

Re: Limp mode? 93 delsol z6

Check timing.
Forum: Tech / Misc
10-20-2014, 10:47 AM
Replies: 20
Views: 3,266
Posted By n/a2boost

Re: OBD1 Custom Wiring harness for Custom car

Man that thing is sweet. What's your location?

You can get rid of the stock pgm-fi relay but you will need to use relays for starter,fuel pump,fan ignition.
Forum: Tech / Misc
10-20-2014, 09:44 AM
Replies: 20
Views: 3,266
Posted By n/a2boost

Re: OBD1 Custom Wiring harness for Custom car

There sensor grounds. D21 is for tps,ect,iat. D22 is for map sensor. What is this harness for/going in?
Forum: Tech / Misc
10-19-2014, 09:44 PM
Replies: 20
Views: 3,266
Posted By n/a2boost

Re: OBD1 Custom Wiring harness for Custom car

The two in yellow are needed.

You can delete all the ones in red. You will need to disable some of them in hondata.
Forum: Tech / Misc
10-02-2014, 03:56 PM
Replies: 5
Views: 14,361
Posted By n/a2boost

Re: Need Ecu Pinouts for d16y7 IACV. Idle Air Control Valve

For 96-98 civic

Black/blue goes to a14

Orange goes to a13.
Forum: Tech / Misc
09-25-2014, 08:30 PM
Replies: 4
Views: 1,012
Posted By n/a2boost

Re: does oil pressure sending unit throw a code?

No code. It's just a light in the cluster.
Forum: Honda / Acura
09-21-2014, 06:55 AM
Replies: 35,398
Views: 10,153,321
Posted By n/a2boost

Re: ♠ Shaved, Tucked, Customized Engine Bays - Pics, Theory, Discussion ♠

Thanks man. Yes it's adhesive duel wall heat shrink. Didn't put the heat shrink to close to the plug cause I don't want to put strain on the wires and I want customers to be able to see the colors...
Forum: Honda / Acura
09-20-2014, 08:19 PM
Replies: 35,398
Views: 10,153,321
Posted By n/a2boost

Re: ♠ Shaved, Tucked, Customized Engine Bays - Pics, Theory, Discussion ♠

437841 (http://s1286.photobucket.com/user/magicman9won4/media/82880F18-5C0F-4482-85C2-3ECE91D1CB7E_zpsuksrsgub.jpg.html)

437842...
Forum: Tech / Misc
09-19-2014, 07:54 AM
Replies: 5
Views: 563
Posted By n/a2boost

Re: Speedo doesn't work

http://i1286.photobucket.com/albums/a608/magicman9won4/A0E282E6-A0DF-4F99-8EFD-9F88B77829FC_zpsjhbwtirv.jpg...
Forum: Tech / Misc
09-04-2014, 07:39 PM
Replies: 9
Views: 3,876
Posted By n/a2boost

Re: speed sensor issue, b series

Check the thermostat ground and all other grounds.
Forum: Tech / Misc
08-22-2014, 06:45 AM
Replies: 13
Views: 1,258
Posted By n/a2boost

Re: 1995 honda civic fan not kicking in.

This^. All so jump the fan switch plug. This is done by taking a piece of wire and touching the two pins in the plug. Ignition switch must be in the on position. If the fan turns on your wiring is...
Forum: Tech / Misc
08-08-2014, 07:09 AM
Replies: 17
Views: 3,505
Posted By n/a2boost

Re: B18C CRX only starts w/ MAP unplugged?

Obd1 and obd2 distributors and alternators work the same,really only difference is the plugs. Obd2 motors have an added crank sensor but jdm motors don't.

Op how did you test the wires? What...
Forum: Tech / Misc
08-07-2014, 03:19 PM
Replies: 12
Views: 1,199
Posted By n/a2boost

Re: Vx harness question

The vx is the only harness to use a 5 wire o2. Most Hondas use a 4 wire o2. So if not using the vx motor or ecu you need to either mod the vx harness to use a 4 wire o2 or mod the ex harness.
Forum: Tech / Misc
08-07-2014, 03:15 PM
Replies: 4
Views: 2,439
Posted By n/a2boost

Re: Vss problems em1

Black/yellow wire should have 12 volts.

Blue/white is the signal wire to cluster and ecu

Black is ground.

Check for power and ground with a multi meter. To check the blue/white wire use a...
Forum: Tech / Misc
07-26-2014, 09:09 PM
Replies: 4
Views: 1,203
Posted By n/a2boost

Re: PLEASE help me finish swap. O2 SENSOR QUESTION

Use an o2 sensor from a 94 integra.
Forum: Tech / Misc
07-22-2014, 07:22 PM
Replies: 9
Views: 4,150
Posted By n/a2boost

Re: H22 no tach

The tach wire is the blue wire in the two wire plug of the distributor.
Forum: Tech / Misc
07-10-2014, 11:10 PM
Replies: 1
Views: 947
Posted By n/a2boost

Re: Parts identification

Red circle is a relay. It's an after market one.

Blue circle is the stock under hood fuse box.

Yellow circle is a factory resistor box. It's for the injectors.
Forum: Tech / Misc
05-13-2014, 06:51 AM
Replies: 5
Views: 3,742
Posted By n/a2boost

Re: OBD0 Distributor on P28?

If using an obd1 or obd2 ecu you must use an obd1 or obd2 distributor. Obd0 distributor won't work with an obd1 or obd2 ecu.
Forum: Tech / Misc
03-30-2014, 12:51 AM
Replies: 6
Views: 786
Posted By n/a2boost

Re: P28 OBD1 converted B18C EK questions

The p72 is plug and play for an obd1 set up and would be the cheaper of the two option. The p28 with a chip and tune will run your set up but costs a lot more.
Forum: Tech / Misc
03-29-2014, 11:59 PM
Replies: 6
Views: 786
Posted By n/a2boost

Re: P28 OBD1 converted B18C EK questions

My guess is the p28 ecu has been chipped and either a base map or tune was done. Open the ecu and see if it's chipped. I wouldn't run it if it hasn't been chipped.

The rywire harness should...
Forum: Tech / Misc
03-27-2014, 11:31 AM
Replies: 9
Views: 1,201
Posted By n/a2boost

Re: How do I unpin my dizzy harness ?

With neddle nose pliers pull the blue piece out of the plug,then with a small flathead watch screw driver lift the tab holding the pin and pull the wire out. The wire/pin will pull out easy if you...
Forum: Tech / Misc
03-21-2014, 06:59 PM
Replies: 3
Views: 2,148
Posted By n/a2boost

Re: OBD2 Scan Tool Not Working-ChaseBays Harness?

You need to connect them to the stock ecu plugs like you did in the pics. I think the purple/black wire goes to c8.
Showing results 1 to 25 of 233
 
Page 1 of 10
1
2
3
Last »


 
Forum Jump


All times are GMT -8. The time now is 05:14 PM.