Honda-Tech - Honda Forum Discussion

Notices
 
Page 1 of 5
1
2
3
Last »
Search: Posts Made By: cctgene
Showing results 1 to 25 of 106
Search took 1.06 seconds.
Forum: Honda Accord (1990 - 2002)
11-27-2014, 06:24 AM
Replies: 3
Views: 4,987
Posted By cctgene

Re: Thumping sound while driving

Have you eliminated the tires as the source of your problem? Sometimes you can get a bubble on the tire tread and get a thump with every rotation.
Forum: Honda Accord (1990 - 2002)
11-02-2014, 09:40 AM
Replies: 12
Views: 1,837
Posted By cctgene

Re: 92 Accord Disappearing and reappearing oil

You might check to see if you have blown head gasket. Water seeping into your oil as the engine cools, thus raising the volume of liquid in your oil pan.

Just a thought.
Forum: Honda Accord (1990 - 2002)
11-02-2014, 09:22 AM
Replies: 10
Views: 2,688
Posted By cctgene

Re: No speedometer

You might check your vss to make sure the drive pin didn't fall out when you installed it.
Happen to me once!

Just a thought.
Forum: Honda Accord (1990 - 2002)
02-05-2013, 08:03 AM
Replies: 10
Views: 889
Posted By cctgene

Re: 1994 Honda Accord EX A/T Turned the Ignition On and just Died?

One simple thing you can do is just connect one side of a jumper cable to the negative
post and the other end to any place on the engine block. If it will now start then you know your dealing with a...
Forum: Honda Accord (1990 - 2002)
02-04-2013, 08:00 AM
Replies: 6
Views: 25,567
Posted By cctgene

Re: Special bolts for ignition switch –Why?

The shear bolts on the column was what I was asking about. The switch itself works fine the problem is that the key is stuck. I don't know if the key lock is available by itself, but none of the...
Forum: Honda Accord (1990 - 2002)
02-04-2013, 07:16 AM
Replies: 6
Views: 25,567
Posted By cctgene

Special bolts for ignition switch –Why?

I’m in the process of replacing the ignition switch on my son’s 96 Accord and it struck me odd that it requires special twist off bolts to hold the switch to the steering column. Anybody know why it...
Forum: Honda Accord (1990 - 2002)
01-25-2013, 11:45 AM
Replies: 13
Views: 13,151
Posted By cctgene

Re: Need help with EGR solinoid valve!!!!! 1991 honda accord

You might check out this site.

home.comcast.net/~em-engineering/T2T013.pdf
Forum: Honda Accord (1990 - 2002)
11-21-2012, 02:40 AM
Replies: 5
Views: 828
Posted By cctgene

Re: Never experienced this problem before. HELP

Now if I move swap plug wires 3 and 4 the problem swaps to these cylinders and 1 and 2 work perfect. if I swap them back 1 and 2 mess up again.

If moving the two spark plug wires moves the...
Forum: Honda Accord (1990 - 2002)
11-08-2012, 11:44 AM
Replies: 48
Views: 2,990
Posted By cctgene

Re: In DESPERATE need of help

Check to make sure your rotor is not loose on the distributor shaft. I believe the rotor on your car does not have a screw, but is kept in place via metal strip spring insert type thing.
Sometimes...
Forum: Honda Accord (1990 - 2002)
10-16-2012, 04:49 AM
Replies: 14
Views: 1,789
Posted By cctgene

Re: HELP!! Fixed broken timing belt - now it doesn't run!!

Check to make sure that your rotor is indeed pointing to the number one spark plug wire when the number one cylinder is at TDC.
Forum: Honda Civic / Del Sol (1992 - 2000)
03-21-2012, 09:53 AM
Replies: 27
Views: 17,430
Posted By cctgene

Re: Need help on how to remove stripped arp head bolt

I've had good success with the Lisle stuck bolt, nut & stud remover tool. However, never use it on a head bolt.

http://www.usatoolwarehouse.com/usatoolwarehouse/LIS-19250.html
Forum: Honda Civic / Del Sol (1992 - 2000)
03-09-2012, 07:01 AM
Replies: 5
Views: 27,888
Posted By cctgene

Re: How much does it cost machine shop to do head?

As a point of reference, I recently replaced the cylinder head on my sons 92 Civic and it cost $400 for the head and another $80 or so for a head gasket set. This was at a cylinder head exchange type...
Forum: Honda Civic / Del Sol (1992 - 2000)
03-08-2012, 11:09 PM
Replies: 27
Views: 22,396
Posted By cctgene

Re: Broke the block where the thermostat housing attaches too...PICS

One thing you could try would be J-B Weld. You would have to clean everything up, including the bolt, and pack the broken area with the stuff and put your housing back on, before it sets up, and run...
Forum: Honda Accord (1990 - 2002)
12-01-2011, 08:51 AM
Replies: 6
Views: 12,208
Posted By cctgene

Re: no compression in one cylinder on my f23

Here's one example of what can cause zero compression!
Forum: Honda Accord (1990 - 2002)
11-09-2011, 10:04 AM
Replies: 5
Views: 25,038
Posted By cctgene

Re: 91 Accord won't start

You might check out the following site, it's a pretty good write up on trouble shooting ignition problems:

http://techauto.awardspace.com/ignition.html

Not sure if the following will be of any...
Forum: Honda Civic / Del Sol (1992 - 2000)
11-05-2011, 01:21 PM
Replies: 2
Views: 2,063
Posted By cctgene

92 Civic LX - no compression in cylinder 3

The engine in my son’s car has some problems. It has No compression in the number 3 cylinder. Doesn’t appear to have the usual classic systems for a bad head gasket, doesn’t overheat, no white smoke...
Forum: Honda Accord (1990 - 2002)
10-28-2011, 05:30 AM
Replies: 5
Views: 3,311
Posted By cctgene

Re: 91 accord no start/dizzy question

There's nothing unique about the pressed on rotor you have I have the same thing on my 91 accord. I don't recall ever having a problem getting it off, it's just held in place by a metal strip spring...
Forum: Honda Accord (1990 - 2002)
10-23-2011, 12:58 PM
Replies: 6
Views: 5,513
Posted By cctgene

Re: 91 Accord Ex hard cold starting/ missfire

Just curious, when you checked the compression was the engine hot or cold?
Forum: Honda Accord (1990 - 2002)
10-21-2011, 10:23 AM
Replies: 4
Views: 2,667
Posted By cctgene

Re: 91 accord electrical problems

You didn't say, but did you have your battery tested?
Forum: Honda Accord (1990 - 2002)
10-10-2011, 07:14 AM
Replies: 6
Views: 3,400
Posted By cctgene

Re: Scratch Noise when turns at very low speed for 96 Honda Accord

You didn't say in your post, but did you replace your CV axles in an effort to get rid of your noise or did the noise appear after you replaced the axles? If the noise appeared after the axles were...
Forum: Honda Accord (1990 - 2002)
12-19-2010, 11:00 AM
Replies: 31
Views: 49,524
Posted By cctgene

Re: Wheel Bearings!

Speaking of wheel bearing, you might find this interesting. My son recently bought a used 96 Honda, and after driving it short time it developed a wheel-bearing type squeak on the front passenger...
Forum: Honda Accord (1990 - 2002)
09-02-2010, 10:49 AM
Replies: 11
Views: 1,518
Posted By cctgene

Re: 90 accord help!

You might check to see that both the block and the head are grounded.
Forum: Honda Accord (1990 - 2002)
08-01-2010, 12:28 AM
Replies: 11
Views: 3,038
Posted By cctgene

Re: Rubbing Noise Hard Cornering

Any chance your axle nut was not torque to specifications?
Forum: Honda Accord (1990 - 2002)
07-13-2010, 04:38 AM
Replies: 60
Views: 58,294
Posted By cctgene

Re: '91 accord f22a1 - no bottem end power?

I wasn’t suggesting doing away with your EGR, I was just asking if you had given any consideration to your problems being EGR related. Your EGR valve should be closed at idle and at the higher rpms...
Forum: Honda Accord (1990 - 2002)
07-12-2010, 12:07 AM
Replies: 60
Views: 58,294
Posted By cctgene

Re: '91 accord f22a1 - no bottem end power?

Have you looked at or eliminated the EGR valve/system as the cause of your problems?
Showing results 1 to 25 of 106
 
Page 1 of 5
1
2
3
Last »


 
Forum Jump


All times are GMT -8. The time now is 12:37 PM.