Honda-Tech - Honda Forum Discussion

Notices
 
Page 1 of 17
1
2
3
11
Last »
Search: Posts Made By: wilham320
Showing results 1 to 25 of 408
Search took 2.06 seconds.
Forum: Forced Induction
09-06-2014, 04:43 PM
Replies: 32,487
Views: 4,868,396
Posted By wilham320

Re: LST / LS-T Turbo B18A B18B setups

Got wot tune done last night, it would make more power every time i turned the boost knob, but I had to stop somewhere w/ stock sleeves.
481whp, 447wtrq. Dyno was on roll speed and was a few...
Forum: Transmission & Drivetrain
08-09-2014, 06:40 PM
Replies: 4
Views: 1,426
Posted By wilham320

Re: s80 trans aftermarket lsd ID

pulled the diff apart today, has metal on metal disks...

So the question now is what fluid to run and does it need friction modifier or not. I probably will run honda MTF if thats good enough. I...
Forum: Transmission & Drivetrain
08-07-2014, 08:51 PM
Replies: 4
Views: 1,426
Posted By wilham320

s80 trans aftermarket lsd ID

Bought a rough shape used s80, pulled it apart and found a 4.06 final drive (65t ring with 16t drive) and seems to be aftermarket lsd.... but i can't figure out what it is. Is the final drive...
Forum: Drag Racing
03-12-2014, 07:54 PM
Replies: 185
Views: 67,020
Posted By wilham320

Re: Gringo's quest to 190mph in the 1/2 mile.

found this on the facebook.... from today @tx2k

http://youtu.be/m3vnh_EY8wM
Forum: Drag Racing
09-09-2013, 01:51 PM
Replies: 79
Views: 7,523
Posted By wilham320

Re: Oil Starvation in Shift-S3ctor 1/2 mile Event, B-series turbo car.

I would have the injectors flowed.... possible that one failed or partial clog on the damaged hole, which could lead to detonation only in that cyl.
Forum: Forced Induction
07-24-2013, 04:01 AM
Replies: 22
Views: 1,903
Posted By wilham320

Re: Stock LS head Turbo dyno soon, what to expect?

grab a 63 a/r hot side, the 48 is gonna be a choke poing past 350 or so....
Forum: Tech / Misc
07-17-2013, 09:15 PM
Replies: 21
Views: 7,958
Posted By wilham320

Re: drilling b series fuel rail for rdx injectors

Edelbrock makes a B Series 14mm fuel rail. It if you want it polished just take some oven cleaner to get the anodize off and hand polish it.
Forum: Forced Induction
07-12-2013, 08:36 PM
Replies: 42
Views: 3,132
Posted By wilham320

Re: Garrett 50 & 57 trim externally the same dimensions?

I figured you would have had a lot higher numbers than 275 at 20psi from a 50 trim...??I saw 375 at 24psi with stock head/cam d16z6 with vitaras and normal length rods. This was on a 60 trim, which...
Forum: Forced Induction
07-12-2013, 02:13 PM
Replies: 42
Views: 3,132
Posted By wilham320

Re: Garrett 50 & 57 trim externally the same dimensions?

You will need to see what size exhaust wheel is on your current 50 trim... Some of the 50 trims had stage 2 turbine wheels, some had stage 3. This will determine what housing you need also. For...
Forum: Forced Induction
07-08-2013, 09:15 PM
Replies: 32,487
Views: 4,868,396
Posted By wilham320

Re: LST / LS-T Turbo B18A B18B setups

All B series OBD2 oil pumps are the same. I see no need to port.
Forum: Forced Induction
07-03-2013, 01:30 AM
Replies: 107
Views: 6,750
Posted By wilham320

Re: guys in 100+ deg dry heat

What fan do you have? Also, what temp does the fan come one at?


Turbo blanket, wrap manifold and downpipe, Get a big bad ass SPAL fan, set fan on temp Via ECU to ~180 ish.
Forum: Forced Induction
06-18-2013, 01:00 AM
Replies: 8
Views: 12,227
Posted By wilham320

Re: gtx3576r redyno results from old 50 trim turbo +60whp !

Did you gain any power at the same boost level?
Forum: Drag Racing
06-06-2013, 08:32 PM
Replies: 27
Views: 2,819
Posted By wilham320

Re: Integra on jack stands, no load, making horrible noise and shaking the motor/tran

I had a similar noise with mine in the air too. I watched the axle and it was flopping around. The Diff in my trans is screwed. With my axle fully seated you can wiggle the inner shaft ~1/4" up and...
Forum: Drag Racing
04-30-2013, 06:44 PM
Replies: 43
Views: 13,686
Posted By wilham320

Re: Faster responding IAT (intake air temp) sensor for OEM based managements?

How does relocating the sensor make it respond faster?? Just due to more air across it vs one runner?
Forum: Forced Induction
04-26-2013, 09:16 PM
Replies: 33
Views: 2,301
Posted By wilham320

Re: Idle problem with different injectors

Of course you can fix the idle... It's called "tuning"
Forum: Forced Induction
04-09-2013, 01:53 AM
Replies: 8
Views: 1,926
Posted By wilham320

Re: Trying to do some math for fmu's

AEM FIC or Greddy Emanage (blue or ultimate)... I used Emanage for about 8 years long ago. Much better tuning than you will ever get out of a FMU. You can retard timing in increments with boost,...
Forum: Forced Induction
04-04-2013, 08:31 PM
Replies: 32,487
Views: 4,868,396
Posted By wilham320

Re: LST / LS-T Turbo B18A B18B setups

Moroso Block filler? I am thinking about doing this to my next block, possibly a b20 block. I'm sure you have seen the thread with the guy who has held ~700 for over a year now.
Forum: Forced Induction
03-22-2013, 01:35 PM
Replies: 3
Views: 609
Posted By wilham320

Re: Intercooler Inquiry

You would have to install it outside the engine bay for it to get ambient air. Otherwise, It would do more harm than good, it would just soak up engine bay heat and make the pipe hotter than it...
Forum: Forced Induction
01-07-2013, 05:20 PM
Replies: 11
Views: 968
Posted By wilham320

Re: RC440s in y8 manifold fitting right?

I forgot about Y8's having the long shouldered stud mounted fuel rail...You need to replace those! Using bolts will not hold the fuel rail straight and at the proper height.

Also... Is there...
Forum: Forced Induction
01-07-2013, 03:02 PM
Replies: 11
Views: 968
Posted By wilham320

Re: RC440s in y8 manifold fitting right?

can you post pic of your RC next to your stock?
Forum: Forced Induction
01-07-2013, 02:58 PM
Replies: 11
Views: 968
Posted By wilham320

Re: RC440s in y8 manifold fitting right?

Seems like your only choice is to let them sit on top. If you have leaks/problems look into injectors that actually fit correctly.
My RC's fit all the way down, but I never used a y8 manifold when...
Forum: Forced Induction
01-07-2013, 02:15 PM
Replies: 11
Views: 968
Posted By wilham320

Re: RC440s in y8 manifold fitting right?

Are the fuel rail spacers installed in the pic? I would remove them to let the rail sit further down, take a Dremel and enlarge the lower seals if they need to be.
Forum: Drag Racing
01-07-2013, 06:39 AM
Replies: 27
Views: 4,839
Posted By wilham320

Re: true street/sfwd door panel predicament

You could trace the outline of the bar interference, cut whats needed, make a foam insert to cover missing section. Throw on some matching interior fabric and glue/screw in place... I think a well...
Forum: Drag Racing
01-02-2013, 09:12 PM
Replies: 31
Views: 6,646
Posted By wilham320

Re: IPGParts.com Tuesday Ten: Chris Miller

"My car is beyond basic, anyone who has spent 10 minutes looking at it can tell you that"

Any pics of the current setup miller?? just curious... haven't seen any pics since last years stuff.
Forum: Drag Racing
12-11-2012, 12:42 AM
Replies: 14
Views: 5,026
Posted By wilham320

Re: 400hp turbo gsr

looks terrible for a small turbo setup... You must have a big boost leak somewhere.
Showing results 1 to 25 of 408
 
Page 1 of 17
1
2
3
11
Last »


 
Forum Jump


All times are GMT -8. The time now is 01:32 AM.