Honda-Tech - Honda Forum Discussion
0 2019/09/21 07:27:44
4 hole pattern is much improved over the stock 1 hole.
4 hole pattern is much improved over the stock 1 hole.
0 2019/09/21 07:27:22
0 2019/09/21 07:27:04
0 2019/09/21 07:26:44
0 2019/09/17 11:56:21
Here's the completed battery tray still in a rough state. My welding is terrible so I always have to weld, then grind into shape, but it works. Next steps are to grind, prime, and then paint. Need to finish this task so we can mock the battery back up and measure all the heavy duty new ground, starter, alternator etc power cables.
Here's the completed battery tray still in a rough state. My welding is terrible so I always have to weld, then grind into shape, but it works. Next steps are to grind, prime, and then paint. Need to finish this task so we can mock the battery back up and measure all the heavy duty new ground, starter, alternator etc power cables.
0 2019/09/15 19:51:15
Started off with an old bed frame for scrap metal.
Started off with an old bed frame for scrap metal.
0 2019/09/15 19:49:23
Ground all the paint off, and cut it in half, saving the part with the slots that we needed.
Ground all the paint off, and cut it in half, saving the part with the slots that we needed.
0 2019/09/15 19:48:57
Then cut the piece with the 2 slots in it intontwo pieces, 1 for each side of the battery tray. The tabs are needed in order to move the mounting point for the j hook on the bolt to attach to - they are too short to reach in the stock battery tray.
Then cut the piece with the 2 slots in it intontwo pieces, 1 for each side of the battery tray. The tabs are needed in order to move the mounting point for the j hook on the bolt to attach to - they are too short to reach in the stock battery tray.
0 2019/09/15 19:48:23
0 2019/09/14 20:25:36
0 2019/09/14 13:22:54
0 2019/09/14 13:22:36
0 2019/09/14 13:22:18
0 2019/09/14 13:21:58
New Ebay silicone hoses. I buy nothing ebay, but these seem ok.
New Ebay silicone hoses. I buy nothing ebay, but these seem ok.
0 2019/09/14 13:21:13
Ported it out to match, used new 66mm gasket as template, marked the overhang material with a sharpie.
Ported it out to match, used new 66mm gasket as template, marked the overhang material with a sharpie.
0 2019/09/14 13:18:50
0 2019/09/14 13:18:31
New 66mm Skunk 2 TB isblarger than the gen1 Skunk 2 intake opening.
New 66mm Skunk 2 TB isblarger than the gen1 Skunk 2 intake opening.
0 2019/09/14 13:17:29
0 2019/09/14 13:17:10
New oem air intake sensor, I copied the trick others have done here shaving down the insulation to provide quicker air temp response for the computer. Hopefully the sensor survived and is still functional! We will see...
New oem air intake sensor, I copied the trick others have done here shaving down the insulation to provide quicker air temp response for the computer. Hopefully the sensor survived and is still functional! We will see...
0 2019/09/14 13:15:45
0 2019/09/14 13:12:14
0 2019/09/06 23:54:33
0 2019/09/06 23:54:06
0 2019/09/06 23:53:49
0 2019/09/06 23:51:50
0 2019/09/04 19:34:25
0 2019/09/03 23:14:04
Cleaned up oil leak area and replaced heater hoses.
Cleaned up oil leak area and replaced heater hoses.
0 2019/09/03 23:13:06
Sneak peek of what's planned for electrical upgrades.
Sneak peek of what's planned for electrical upgrades.
0 2019/09/03 23:11:10
Planning on running new higher gauge starter power wire.
Planning on running new higher gauge starter power wire.
0 2019/09/03 23:09:42
0 2019/09/03 22:58:39
0 2019/09/03 22:58:02
.
.
0 2019/09/03 22:57:27
Igniters are actually different slightly as seen in the photo, but they both fit
Igniters are actually different slightly as seen in the photo, but they both fit
0 2019/09/03 22:56:52
0 2019/09/03 22:56:31
0 2019/09/03 22:56:06
0 2019/09/03 22:54:33
0 2019/08/28 19:43:05
0 2019/08/28 19:42:46
0 2019/08/28 18:42:15