Honda-Tech - Honda Forum Discussion
0 2019/11/10 08:36:09
0 2019/11/10 08:36:02
0 2019/11/10 08:35:54
0 2019/11/10 08:35:47
0 2019/11/09 00:26:31
0 2019/11/09 00:26:23
0 2019/11/09 00:26:14
0 2019/11/09 00:26:05
0 2019/11/09 00:25:57
0 2019/11/09 00:25:48
0 2019/11/06 10:09:51
Used grommet so wires wont get cut up
Used grommet so wires wont get cut up
0 2019/10/30 22:41:24
0 2019/10/30 22:40:46
In process
In process
0 2019/10/30 22:40:18
Closer
Closer
0 2019/10/30 22:39:19
Quality flanges
Quality flanges
0 2019/10/24 21:05:24
Good quality hand tig welded.
Good quality hand tig welded.
0 2019/10/24 21:05:17
Piping starts off at 2.5" for only a short length (~3"), then expands to 3" mandrel bent for the rest of the exhaust system. If not desired you could cut off and add a 3" pipe the full length.
Piping starts off at 2.5" for only a short length (~3"), then expands to 3" mandrel bent for the rest of the exhaust system. If not desired you could cut off and add a 3" pipe the full length.
0 2019/10/24 21:05:09
Comes in 3 pieces
Comes in 3 pieces
0 2019/10/24 21:05:01
Muffler and resonator are both large.
Muffler and resonator are both large.
0 2019/10/24 21:04:54
0 2019/10/20 16:47:43
0 2019/10/20 15:23:18
0 2019/10/20 15:15:24
0 2019/10/20 15:14:57
0 2019/10/20 15:07:23
0 2019/09/30 22:12:13
0 2019/09/30 22:11:58
0 2019/09/30 22:11:44
0 2019/09/26 18:59:16
0 2019/09/26 18:44:12
0 2019/09/26 18:43:56
0 2019/09/26 18:43:42
0 2019/09/26 18:43:25
The heater valve has 3 small screws, 2 for attaching it to the firewall mount, and 1 for the valve lever. If the screws are rusty you can replace all 3 with this size screw, I used stainless of course like most of the other hardware being replaced.
The heater valve has 3 small screws, 2 for attaching it to the firewall mount, and 1 for the valve lever. If the screws are rusty you can replace all 3 with this size screw, I used stainless of course like most of the other hardware being replaced.
0 2019/09/21 07:51:39
Top view. Will probably paint or powder coat this and several other brackets.
Top view. Will probably paint or powder coat this and several other brackets.
0 2019/09/21 07:51:20
The adapter harness fits the new injector, but the other end of the adapter doesnt fit the engine wire harness. Not sure if its an OBD1 vs OBD2 thing or some other issue..
The adapter harness fits the new injector, but the other end of the adapter doesnt fit the engine wire harness. Not sure if its an OBD1 vs OBD2 thing or some other issue..
0 2019/09/21 07:33:59
0 2019/09/21 07:33:21
Heres an oem fuel rail stud length in case you need it.
Heres an oem fuel rail stud length in case you need it.
0 2019/09/21 07:32:32
I couldn't remove the broken stud from the intake manifold with regular pliers or vice grips, these however worked great and made the job easy. Highly recommended.
I couldn't remove the broken stud from the intake manifold with regular pliers or vice grips, these however worked great and made the job easy. Highly recommended.
0 2019/09/21 07:30:27
Also not sure if the black plastic around the tip of the injector is supposed to be removed, or thats just how it is?
Also not sure if the black plastic around the tip of the injector is supposed to be removed, or thats just how it is?
0 2019/09/21 07:28:20