Honda-Tech - Honda Forum Discussion
0 2023/04/12 16:42:09
TRS delivery!
TRS delivery!
0 2023/04/12 16:38:53
0 2023/04/12 12:18:22
Projector in the reflector!
Projector in the reflector!
0 2023/04/02 16:36:23
Morimoto Mini H1 8.0 going into a Spec D housing.
Morimoto Mini H1 8.0 going into a Spec D housing.
0 2023/04/01 13:25:02
Jumper wire did not reveal any ABS codes - a clue!
Jumper wire did not reveal any ABS codes - a clue!
0 2022/11/18 13:50:39
A little nasty
A little nasty
0 2022/11/18 13:50:28
Cleaned up
Cleaned up
0 2022/11/18 13:50:22
The light came on after the ABS bleed!
The light came on after the ABS bleed!
0 2022/11/18 13:49:50
0 2022/10/23 12:38:30
0 2022/10/23 12:34:06
0 2022/10/23 12:24:08
Alternate vacuum line routing until I figure things out...
Alternate vacuum line routing until I figure things out...
0 2022/04/18 15:57:51
0 2021/06/08 15:01:16
0 2021/06/08 15:00:33
0 2021/05/16 19:38:29
0 2021/05/16 19:36:49
0 2021/05/16 19:36:27
New pressure switch port = a little over 8mm. WTF?!?
New pressure switch port = a little over 8mm. WTF?!?
0 2021/05/16 19:32:15
Old pressure switch port = 9.5mm
Old pressure switch port = 9.5mm
0 2021/05/16 19:31:36
0 2021/05/16 19:31:11
0 2021/05/16 19:29:57
0 2021/05/16 19:26:24
0 2021/05/16 19:12:31
0 2021/05/16 19:07:33
Yes, better access! There is a 10mm up to the front of the reservoir, and another up on the neck - very difficult to get to.
Yes, better access! There is a 10mm up to the front of the reservoir, and another up on the neck - very difficult to get to.
0 2021/05/16 11:53:25
I thought it would be a lot easier to drop the windshield washer reservoir out of the way with the bumper skin off, so here we go!
I thought it would be a lot easier to drop the windshield washer reservoir out of the way with the bumper skin off, so here we go!
0 2021/05/16 11:52:09
Peel back the inner fender liner and see the clamp holding the dryer in place
Peel back the inner fender liner and see the clamp holding the dryer in place
0 2021/05/16 11:51:07
Here is how things look from the top to replace the Dryer
Here is how things look from the top to replace the Dryer
0 2021/05/16 11:49:44
0 2021/05/10 07:46:31
Front hard line has an o-ring joint at the condensor, the rear hard line has a mount to the fan shroud
Front hard line has an o-ring joint at the condensor, the rear hard line has a mount to the fan shroud
0 2021/05/10 07:45:14
Remove the relays from their mount
Remove the relays from their mount
0 2021/05/10 07:44:41
These seem like a good place to start!
These seem like a good place to start!
0 2021/05/10 07:38:56
Lots or o-rings in this vicinity
Lots or o-rings in this vicinity
0 2021/05/10 07:38:28
0 2021/05/05 15:40:29
0 2021/05/05 14:29:03
0 2021/04/22 18:04:23
0 2021/04/22 18:04:16
0 2021/04/22 18:04:08
0 2021/04/04 12:21:59