Honda-Tech - Honda Forum Discussion
0 2023/05/13 09:26:31
0 2023/05/13 09:26:26
Measure the install depth.
Measure the install depth.
0 2023/05/13 09:22:07
41 cm, just under.
41 cm, just under.
0 2023/05/13 09:21:58
I placed the bearing plate on some pieces of wood and tapped the shaft out.
I placed the bearing plate on some pieces of wood and tapped the shaft out.
0 2023/05/13 09:21:52
Remove the bearing retainer.
Remove the bearing retainer.
0 2023/05/13 09:21:41
A close up of the pickup
A close up of the pickup
0 2023/05/13 09:18:12
Keep track of the ignitor connections!
Keep track of the ignitor connections!
0 2023/05/13 09:18:06
Now the shaft slides out of the housing - note the old seal.
Now the shaft slides out of the housing - note the old seal.
0 2023/05/13 09:17:57
Measure the install depth of the counterweight.
Measure the install depth of the counterweight.
0 2023/05/13 09:14:01
18 cm
18 cm
0 2023/05/13 09:13:53
Gently pry off w/ screwdrivers.
Gently pry off w/ screwdrivers.
0 2023/05/13 09:13:47
0 2023/05/13 09:10:03
Remove the coil tower.
Remove the coil tower.
0 2023/05/13 09:02:49
Free the wiring harness from the holder.
Free the wiring harness from the holder.
0 2023/05/13 09:02:39
Coil is removed in this picture, ignitor remains in place (lower right of picture).
Coil is removed in this picture, ignitor remains in place (lower right of picture).
0 2023/05/13 09:02:28
Finished w/ the mods to halo.
Finished w/ the mods to halo.
0 2023/05/12 16:22:53
I drilled 3 holes for the halo mounts.
I drilled 3 holes for the halo mounts.
0 2023/05/12 16:22:45
I clearanced the shroud for the halo wiring.
I clearanced the shroud for the halo wiring.
0 2023/05/12 16:22:40
Finished securing the halo to the shroud.
Finished securing the halo to the shroud.
0 2023/05/12 16:22:34
I used fishing line - hard to see!
I used fishing line - hard to see!
0 2023/05/12 16:22:26
Next - secure the shroud to the projector.
Next - secure the shroud to the projector.
0 2023/05/12 16:22:21
Projector back in the reflector bowl.
Projector back in the reflector bowl.
0 2023/05/12 16:22:13
Test fire the halo.
Test fire the halo.
0 2023/05/12 16:22:04
Test the switchback function.
Test the switchback function.
0 2023/05/12 16:21:56
0 2023/05/10 14:25:33
0 2023/05/10 07:15:55
0 2023/05/10 07:15:41
0 2023/05/07 11:44:53
0 2023/05/07 11:44:43
This H4 relay harness is from Morimoto.
This H4 relay harness is from Morimoto.
0 2023/05/07 11:39:56
The high beam connection looks like connects directly to the Mini H1s - no adapter.
The high beam connection looks like connects directly to the Mini H1s - no adapter.
0 2023/05/07 11:39:43
0 2023/05/03 10:07:02
0 2023/05/03 10:03:33
Here the Moto-Holder base is screwed onto the projector housing. Note the slot for the ground rod of the bulb to pass through. Also note the dimple at 7 or 8 o'clock to mate w/ the horseshoe clip.
Here the Moto-Holder base is screwed onto the projector housing. Note the slot for the ground rod of the bulb to pass through. Also note the dimple at 7 or 8 o'clock to mate w/ the horseshoe clip.
0 2023/04/28 13:42:30
H1 bulb w/ ground rod on left.
H1 bulb w/ ground rod on left.
0 2023/04/28 13:42:23
Bulb w/ horseshoe clip. Not the recess that aligns w/ the dimple.
Bulb w/ horseshoe clip. Not the recess that aligns w/ the dimple.
0 2023/04/28 13:42:15
Bulb w/ Moto-Holder base. I un-screwed the base from the projector housing.
Bulb w/ Moto-Holder base. I un-screwed the base from the projector housing.
0 2023/04/28 13:42:09
More fail.
More fail.
0 2023/04/28 13:28:20
Here is how the H1 Mini ships the wiring for the high/low cut-off shield.
Here is how the H1 Mini ships the wiring for the high/low cut-off shield.
0 2023/04/28 13:21:27