Honda-Tech - Honda Forum Discussion
0 2023/08/27 18:39:30
Adjusting Bolt has 12mm lock nut down at the base:
Adjusting Bolt has 12mm lock nut down at the base:
0 2023/08/27 18:39:26
Here is how the advance looked:
Here is how the advance looked:
0 2023/08/27 18:28:18
FSM timing procedure:
FSM timing procedure:
0 2023/08/27 18:28:15
No more CEL!
No more CEL!
0 2023/08/27 18:21:25
0 2023/08/27 18:18:49
Possible I put this back in upside down?
Possible I put this back in upside down?
0 2023/08/21 15:01:17
0 2023/08/18 14:45:52
0 2023/08/06 18:09:04
0 2023/08/06 18:09:00
Oh noes!
Oh noes!
0 2023/08/06 17:59:56
0 2023/08/06 17:59:50
0 2023/08/06 17:53:12
A little crusty looking:
A little crusty looking:
0 2023/06/11 18:51:04
I dropped the original ignitor back in place:
I dropped the original ignitor back in place:
0 2023/06/11 18:50:58
Before:
Before:
0 2023/06/11 18:50:53
Clean the threads on the screws:
Clean the threads on the screws:
0 2023/06/11 18:50:49
After:
After:
0 2023/06/11 18:50:44
0 2023/06/10 08:34:26
Fire in the hole!
Fire in the hole!
0 2023/06/10 08:34:21
NAPA p/n in parens...
NAPA p/n in parens...
0 2023/06/10 05:11:33
New seal is in!
New seal is in!
0 2023/06/09 07:53:09
Test fit the cracked bearing plate in the housing.
Test fit the cracked bearing plate in the housing.
0 2023/06/07 07:18:49
The crack in the plate is tightened up:
The crack in the plate is tightened up:
0 2023/06/07 07:18:41
Claw the old seal out:
Claw the old seal out:
0 2023/06/07 07:16:02
The spring side of the seal goes towards the engine and oil.
The spring side of the seal goes towards the engine and oil.
0 2023/06/07 07:15:53
Put your supports in nice and close to center - under the raised lip.
Put your supports in nice and close to center - under the raised lip.
0 2023/06/07 07:13:30
Confirm your install depth.
Confirm your install depth.
0 2023/06/07 07:13:23
Don't spread your supports out this wide:
Don't spread your supports out this wide:
0 2023/06/07 07:11:19
Oh noes!
Oh noes!
0 2023/06/07 07:11:10
0 2023/05/29 04:41:46
Old bearing:
Old bearing:
0 2023/05/27 14:02:34
Less than 13mm
Less than 13mm
0 2023/05/27 14:02:28
0 2023/05/18 10:05:59
Trying to level the projectors.
Trying to level the projectors.
0 2023/05/18 10:05:50
Looking at this pic, I should remove the Phillips fasteners that are no longer needed. I would hate for them to come loose and interfere with the brights.
Looking at this pic, I should remove the Phillips fasteners that are no longer needed. I would hate for them to come loose and interfere with the brights.
0 2023/05/16 08:48:17
0 2023/05/16 08:06:25
0 2023/05/13 09:26:46
0 2023/05/13 09:26:41
0 2023/05/13 09:26:36