Honda-Tech - Honda Forum Discussion
0 2016/07/15 22:57:44
0 2016/07/15 22:57:47
0 2016/07/15 22:57:49
0 2016/07/15 22:57:58
0 2016/07/15 22:58:00
0 2016/07/15 23:04:32
0 2016/07/15 23:04:35
0 2016/07/15 23:04:41
0 2016/07/15 23:04:44
0 2016/07/15 23:04:55
test fit
test fit
0 2016/07/15 23:05:01
0 2016/07/15 23:05:07
0 2016/07/15 23:05:10
0 2016/07/15 23:05:14
96-97
96-97
0 2016/08/02 20:02:01
94-95
94-95
0 2016/08/02 20:02:02
0 2016/10/31 18:19:35
0 2016/11/04 09:17:36
0 2016/11/04 09:21:57
0 2016/11/04 09:31:48
1st time it's hits the rev limiter @6009rpm then dips...
1st time it's hits the rev limiter @6009rpm then dips...
0 2016/11/07 09:20:07
and comes back up a 2nd time and peaks @6048rpm and I let off the throttle...
and comes back up a 2nd time and peaks @6048rpm and I let off the throttle...
0 2016/11/07 09:21:47
These are 3 piece/chamber tanks. The middle has the main baffle material (stainless brillo), the top has an air filter material (charcoal filter), and the bottom is just a drainage tank (with a 5/16 nut welded on and plugged w/bolt and rubber washer, for emptying it)
These are 3 piece/chamber tanks. The middle has the main baffle material (stainless brillo), the top has an air filter material (charcoal filter), and the bottom is just a drainage tank (with a 5/16 nut welded on and plugged w/bolt and rubber washer, for emptying it)
0 2016/11/17 14:13:32
I forget the size of these fittings?...maybe 3/4in npt? Whatever it is, it fits VERY snuggly into -10AN stainless hose from Vibrant.
I forget the size of these fittings?...maybe 3/4in npt? Whatever it is, it fits VERY snuggly into -10AN stainless hose from Vibrant.
0 2016/11/17 14:14:19
Here you can see the stainless scouring pad material used in the main baffle chamber.
Here you can see the stainless scouring pad material used in the main baffle chamber.
0 2016/11/17 14:14:32
Stainless mesh for top
Stainless mesh for top
0 2016/11/17 14:14:46
And here I just used zip-ties to hold each of the tanks together, which made it much easier to mount them on the firewall.
And here I just used zip-ties to hold each of the tanks together, which made it much easier to mount them on the firewall.
0 2016/11/17 14:16:19
I used a sanding disc on the angle grinder to grind off the tops of the rivets in order to remove the baffle plate.
I used a sanding disc on the angle grinder to grind off the tops of the rivets in order to remove the baffle plate.
0 2016/11/17 14:29:56
Took this pic to note the position of the holes in the baffle plate vs the holes in the actual VC that I drilled. This is VERY IMPORTANT... The holes you make in the VC have to be in the chambers opposite the holes in the baffle plate so that the gasses are forced through the baffle chambers. Otherwise you'd just be blowing oil out of your VC and into your catch tanks.
Took this pic to note the position of the holes in the baffle plate vs the holes in the actual VC that I drilled. This is VERY IMPORTANT... The holes you make in the VC have to be in the chambers opposite the holes in the baffle plate so that the gasses are forced through the baffle chambers. Otherwise you'd just be blowing oil out of your VC and into your catch tanks.
0 2016/11/17 14:30:15
0 2016/11/17 14:30:34
0 2016/11/17 14:30:51
Then used a 7/8in bit to drill out the holes for the fittings.
Then used a 7/8in bit to drill out the holes for the fittings.
0 2016/11/17 14:31:11
0 2016/11/17 14:31:55
9/64 bit to drill pilot holes for the tap
9/64 bit to drill pilot holes for the tap
0 2016/11/17 14:40:31
These are 3 piece/chamber tanks. The middle has the main baffle material (stainless brillo), the top has an air filter material (charcoal filter), and the bottom is just a drainage tank (with a 5/16 nut welded on and plugged w/bolt and rubber washer, for emptying it)
These are 3 piece/chamber tanks. The middle has the main baffle material (stainless brillo), the top has an air filter material (charcoal filter), and the bottom is just a drainage tank (with a 5/16 nut welded on and plugged w/bolt and rubber washer, for emptying it)
0 2016/11/17 14:53:51
I forget the size of these fittings?...maybe 3/4in npt? Whatever it is, it fits VERY snuggly into -10AN stainless hose from Vibrant.
I forget the size of these fittings?...maybe 3/4in npt? Whatever it is, it fits VERY snuggly into -10AN stainless hose from Vibrant.
0 2016/11/17 14:54:32
Here you can see the stainless scouring pad material used in the main baffle chamber.
Here you can see the stainless scouring pad material used in the main baffle chamber.
0 2016/11/17 14:54:45
Stainless mesh for top
Stainless mesh for top
0 2016/11/17 14:55:00
And here I just used zip-ties to hold each of the tanks together, which made it much easier to mount them on the firewall
And here I just used zip-ties to hold each of the tanks together, which made it much easier to mount them on the firewall
0 2016/11/17 14:56:07
First I had to use a sanding disc on the die grinder to grind off the rivet heads in order to remove the baffle plate
First I had to use a sanding disc on the die grinder to grind off the rivet heads in order to remove the baffle plate
0 2016/11/17 14:58:37