Itr or b16 or B17 sk2 built pr-3 head needed
#1
Honda-Tech Member
Thread Starter
Itr or b16 or B17 sk2 built pr-3 head needed
Hey I have a 98 gsr with a b18c5 installed. It only has come low comp pistons maybe some after market rods and bearings but all I know is cp pistons (I bought it online from a guy who barely spoke English for $1800 and it’s leaked from the headgasket ever since it was installed 3 years ago and the head has a ticking noise when cold started. I do have 3 pr3 heads but only one I would send out and then I’d have to find the caps and bolts for it. So I’m looking for another one that’s hopefully skunk2 built already. I have a go auto works turbo kit sitting since last year now since I can’t make my mind up or find a cheap built head from a trustworthy place or person. Please let me know?? I am in Ontario Canada thanks Rob
#2
Honda-Tech Member
Re: Itr or b16 or B17 sk2 built pr-3 head needed
Why not pull off the C5 head and just have it rebuilt? send it a reputable shop not some from some shop you have no info from or joe shmoes machine shop, they are a dime a dozen and half the work is half assed. Send that head C5 head to 4 piston to be properly ported and rebuilt or to Ramey Engines, The b18C5 you have in there is already the best flowing B series head, just have it rebuilt and ported and polished! I would have the bottom block torn down and re checked! and re surfaced before you put the head back on.
https://www.facebook.com/4Piston/
https://www.facebook.com/RameyRaceEngines/
https://www.facebook.com/4Piston/
https://www.facebook.com/RameyRaceEngines/
#3
Honda-Tech Member
Thread Starter
Re: Itr or b16 or B17 sk2 built pr-3 head needed
Thank you so much for the advice and info. It’s hard here in Ottawa to get a good Honda people who love them to work on them. The place I was going to send it was Canadian cylinder head in Toronto. But I daily the car to work and back so I can’t send this head but have another one I could. But for all skunk2 internals and ported polished it will cost me over 2-2,500$ Canadian so I figured I might find one already built for about the same price. I have to check out those sites thank you for that as I have a hard time finding good prices on type r parts
#4
Honda-Tech Member
Re: Itr or b16 or B17 sk2 built pr-3 head needed
Thank you so much for the advice and info. It’s hard here in Ottawa to get a good Honda people who love them to work on them. The place I was going to send it was Canadian cylinder head in Toronto. But I daily the car to work and back so I can’t send this head but have another one I could. But for all skunk2 internals and ported polished it will cost me over 2-2,500$ Canadian so I figured I might find one already built for about the same price. I have to check out those sites thank you for that as I have a hard time finding good prices on type r parts
http://www.4pistonracing.com/outlaw-gsr-head
Just add,
- Disassemble +$50.00
- Assemble +$50.00
- Hot Tank + Soda Blast +$50.00
The following users liked this post:
#5
Honda-Tech Member
Thread Starter
Re: Itr or b16 or B17 sk2 built pr-3 head needed
Just send your head to 4 piston and they will give you a outlaw head for around $1,740 with SK2 VT,
4P Outlaw V2 GSR CNC Head | 4 Piston Racing
Just add,
4P Outlaw V2 GSR CNC Head | 4 Piston Racing
Just add,
- Disassemble +$50.00
- Assemble +$50.00
- Hot Tank + Soda Blast +$50.00
definitely getting a Ramey motor for sure. Thanks man. I looked and asked and I think I’m just sending them the motor to rebuild I can’t wait but I might wait till next year when I’m debt free. Going to be awesome Ramey b18c5 . Thanks so much very much appreciated
Thread
Thread Starter
Forum
Replies
Last Post