Just wondering what size injectors and fuel pump I'm going to need? Also would like a little more info on which cams to run? This car will be for semi daily driving an drag and maybe a little bit of SCCA.

Here is my setup.
b16 block GE sleeved bored 84mm
Je 12.5.1 comp. pistons
eagle rods
micropolished and champhered (sp) crank
alaniz p/p head w/ highlift valve springs and retainers
jun 3, toda c's, or ef-1 camsneed more info on these
skunk2 IM with 68mm or 70 mm t/b
HeaderTech header
AEM CAI
JDM ITR or Y21 trans with 4.78 and lsd
clutchmasters flywheel and stage 3 clutch

All to be tuned w/ Hondata or AEM EMS

Thanx in advance.

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by EG-cellent &raquo;</TD></TR><TR><TD CLASS="quote">Just wondering what size injectors and fuel pump I'm going to need? Also would like a little more info on which cams to run? This car will be for semi daily driving an drag and maybe a little bit of SCCA.

Here is my setup.
b16 block GE sleeved bored 84mm
Je 12.5.1 comp. pistons
eagle rods
micropolished and champhered (sp) crank
alaniz p/p head w/ highlift valve springs and retainers
jun 3, toda c's, or ef-1 camsneed more info on these
skunk2 IM with 68mm or 70 mm t/b
HeaderTech header
AEM CAI
JDM ITR or Y21 trans with 4.78 and lsd
clutchmasters flywheel and stage 3 clutch
</TD></TR></TABLE>

at least 310cc injectors, 55psi fuel pressure and walbro 195lph or supra/rx7 fd3s/mitsu 2liter turbo fuel pumps

greg

 

Would 370's be overkill and should I run an intank pump or inline one?
Thanx

 

I have almost the exact same setup and i was advised to use 270 or 310 cc injectors. If you plan on using Hondata go up to 440's, you'll just run a lower duty cycle (ie your injectors won't work as hard). My motor will go together in 3 weeks, except i have 84.5 mm sleeves.

 

I use 310's w/ a somewhat similar seup. If you get a hondata, there will be no such thing as overkill as far as the injectors are concerned.

 

just get 370s and 255LPH intank...

 

What other things would you do to or change about my setup?

 

what would i change, lol this is not for you but:::
b16 block GE sleeved bored 84mm CHANGE
Je 12.5.1 comp. pistons CHANGE
eagle rods CHANGE
micropolished and champhered (sp) crank CHANGE
alaniz p/p head w/ highlift valve springs and retainers CHANGE
jun 3, toda c's, or ef-1 camsneed more info on these CHANGE
skunk2 IM with 68mm or 70 mm t/b CHANGE
HeaderTech header CHANGE
AEM CAI CHANGE
JDM ITR or Y21 trans with 4.78 and lsd
clutchmasters flywheel and stage 3 clutch CHANGE

thats me though..i would telly uo what id change it to, but thats my motor setup, lol..shh

 

Yeah that was really helpful

it all good though!

 

As for your cams, I personally think that Toda c's are a little too much for the street, but that just me. The JUN 3's are a little more tame so they would be my choice.

 

you should be fine with 310's I don't see any need for any bigger on that setup.

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by EG-cellent &raquo;</TD></TR><TR><TD CLASS="quote">What other things would you do to or change about my setup?</TD></TR></TABLE>
ha thats y u asked me what I would do lol...

 

https://honda-tech.com/zeroforum?id=44