My friend used the turbo-performance.com kit and it was like 70 bucks.. but the kid sucked. Everyone says to use the Earl fittings from some street rod site.. which I agree with but I did a totaling of all of the fittings and it was like 200 dollars! that's insane for an oil line kit. A couple of the fittings where swivel and they were like 30 alone. Is it asbolutely Necessary to get these swivel pieces? thanks! if anyone knows of a good kit or order list let me know please.

 

are you sure it is 200.00, i paid like 100.00 for my drain/feed kit, i used earls fittings for the drain and a nos -3AN line for the feed line.

 

do you possibly have a parts list from when you bought it? I found a list from amstreetrod in the archived section and no lie it was at like 140 when i said forget this.. and i was 3/4 of the way done the list..

 

I was there slivereh2 paid like a bill for his setup, and its nice.

 

do you have a parts list you can get me? also where did you get it from? thanks man!

 

Pepboys, yeeeaaahhhhh. Na I think he got his stuff from summit.

 

anyone got a parts list from summit? i've seen the amstreetrod list.. but that's the one that was real expensive for the kit.. thanks

 

Braided lines are not cheap. Cheapest though is at racerpartswholesale.com.

 

Theres another place around called hosefast I believe, they are resonably priced.

 

haha i paid a total of 50 bucks for mine ... go to amstreetrod.com

and get the speedflex hose, its SS braided, teflon, with straight swivel seal fittings on it . and its like 20$ !!!!

 

i got my ish from vsv, they have a website it is vsvperformance.com

 

anyone got a parts list from summit?

 

Info provided by Fleminco-T:

Oil Return Parts list

Oil Drain Flange 1/2"

1/2" to -10AN adapter [981610erl]

2 of 45 deg or straight -10AN swivel seal hose ends [804610erl or 800110erl]

1' to 1.5' of -10 Performo flex lines [400100erl]

Steel -10 weld on bung [967110erl]


Oil feed line part list

1- male 1/8" BSPT to female 1/8" NPT adapter (aluminum)
1- 1/8" NPT Brass Tee adapter with one male out and two females.
1- 3.5' of -3AN lines with hose ends attach
1- straight 1/8" NPT to -3AN adapter
1- 90 deg 1/8" NPT to -3AN adapter

 

Do all turbos take the same size feed kit?

 

Here is a good diagram of what you will need if you want to hook up an oil pressure guage too

 

look into gettin one from jgs. the site is http://www.jgstools.com/turbo/

 

Here is my writeup, very cheap and very nice feed line.


https://honda-tech.com/zerothread?id=432769

 

Please check this thread.

 

delete "orig.jpg" at the end...

 

no, 4 bolts take different feed lien than 5 bolts, DSM and Mitsu turbo are different as well..

stan

 

nice diagram!

 

I get all of my fittings and stuff from a local Rubber company....

I use the Teflon bradied steel lines, and the fittings for it are 1/2 the price or more. I also get the high pressure clamps from them for super cheap...

 

I pieced together my own fedd/drain kit and it only cost me about $70, with all earl's fitting and braided lines.

 

For what application or does it matter? I have a heater hose temporarily for my B16Drag civic. I want to replace it with Earl's, but don't know what all is needed?

 

the return will work on all T3 cartridge based turbo liek T3, T3/4e, b and etc