DJ_SaNdOz

Jesus Kelly - that's a helluva quick power increase from 5-6k how's traction in the first few gears when that spools? I bet 5th gear on the highway is crazy.

SovXietday

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by DJ_SaNdOz &raquo;</TD></TR><TR><TD CLASS="quote">Jesus Kelly - that's a helluva quick power increase from 5-6k how's traction in the first few gears when that spools?</TD></TR></TABLE>

360ft/lbs SOHC is also known as a tire liquifierer.

b18_ef_hatch

Kelly. I like that dyno chart I hope by next June I can be somewhere near that and running 11's or 12's in the 1/4 mile My build is in my sig below, updated as I get stuff done.

siregcivic

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by sXekid &raquo;</TD></TR><TR><TD CLASS="quote">what are you boosting? stock wastegate?</TD></TR></TABLE>

12 psi d15z1 block y8 head 8.04:1 compression.. stock internal wg with manual boost controller.. this setup has some boost lag but i figure its just because of the low compression.. but when it pics up.. its alot of fun

my last motor ( just blew bad oil pump ) d16z6/ y8 head shaved 20 at 10 psi, was almost always in boost.. on the freeway, anytime i would go up a slight hill it would full boost at 1/8 throttle

broketuner-Sol_Si

NM I found it!

http://www.homemadeturbo.com/f...569.0


whoever's this is


Modified by broketuner-Sol_Si at 11:09 PM 12/18/2006

confucioussae

iTrader: (1)

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Kelly. &raquo;</TD></TR><TR><TD CLASS="quote">
from ~5300 rpms, you better have both hands on the wheel </TD></TR></TABLE>

huge jump from 5-6k, great numbers on the sohc !

mike93eh2

well yours is a little better since youre making more power.

but damn 30 psi on a 57 trim? mine was done at 25psi..sc34 ball bearing .63 exhaust

but im only running 22psi.

krazyhmongboi

td05 turbine/hf manifold
push'n 8 pounds right now
2.5 inch downpipe
255lph walbro fuel pump
450cc injectors
p28 ecu chipped
intercooler
greddy type s bov
going to get tuned soon

no numbers..anione have an idea what i will be getting?


anione?

661rex89si

hey how much is too much shaft play on a t3 42 48 a.r turbo

Kelly.

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by DJ_SaNdOz &raquo;</TD></TR><TR><TD CLASS="quote">Jesus Kelly - that's a helluva quick power increase from 5-6k how's traction in the first few gears when that spools? I bet 5th gear on the highway is crazy.</TD></TR></TABLE>

i cant even get my M&H roadmasters (bais ply street tire) to stick in 1-3rd gear
that is at ~25psi or so,

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by b18_ef_hatch &raquo;</TD></TR><TR><TD CLASS="quote">Kelly. I like that dyno chart I hope by next June I can be somewhere near that and running 11's or 12's in the 1/4 mile My build is in my sig below, updated as I get stuff done.</TD></TR></TABLE>
with the power im making, id hope to see low 11s,
but im a hoorible driver, so we will see

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by confucioussae &raquo;</TD></TR><TR><TD CLASS="quote">
huge jump from 5-6k, great numbers on the sohc ! </TD></TR></TABLE>
thanks,
this was done over the summer,
car got a ~40 psi boost spike and cracked a sleeve.
the new motor will be in this weekend and retuned on jan 5th.
with a fresh turbo and a fresh block, i hope to crack the 450 mark

Kelly.

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by mike93eh2 &raquo;</TD></TR><TR><TD CLASS="quote">well yours is a little better since youre making more power.

but damn 30 psi on a 57 trim? mine was done at 25psi..sc34 ball bearing .63 exhaust

but im only running 22psi.</TD></TR></TABLE>

turn it up

SovXietday

Same turbo Kelly?

Kelly.

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by SovXietday &raquo;</TD></TR><TR><TD CLASS="quote">Same turbo Kelly? </TD></TR></TABLE>

yeah,
same t3t4e 57 trim
63 turbine

i sent the turbo to a friend to have it freshened up
so i hope to see alittle gain from that.

theSQad

YAY !!!

everyone go to http://www.d-series.org and look at all the awesome turbo SOHCs there

DJ_SaNdOz

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by theSQad &raquo;</TD></TR><TR><TD CLASS="quote">YAY !!!

everyone go to http://www.d-series.org and look at all the awesome turbo SOHCs there

</TD></TR></TABLE>

Spammer

SovXietday

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Kelly. &raquo;</TD></TR><TR><TD CLASS="quote">yeah,
same t3t4e 57 trim
63 turbine

i sent the turbo to a friend to have it freshened up
so i hope to see alittle gain from that. </TD></TR></TABLE>



I pulled apart my Z6 the other night, bearings were in good shape, no scoring on cylinder walls, hell even the pistons and rods were fine. Going to talk to the machine shop guy as soon as I get the chance to get prices etc.

splitime

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by theSQad &raquo;</TD></TR><TR><TD CLASS="quote">YAY !!!

everyone go to http://www.d-series.org and look at all the awesome turbo SOHCs there

</TD></TR></TABLE>

Why waste time there, when there is HT, HMT and turboD16. All have a better pool of knowledge for Turbo D people

S@nt0s

well guys Xmas came a lil early for me.. altho its nothign crazy but it is well worth posting.....

i got a call from my good Friend Bisi and asked for my addy.. this was YESTERDAT mind you... today i come home early and find this waiting for me.....

WOW it brought a to my face...





i lov eit... threw me off a min. but then i saw the small print!! a must have for you SOHC'ers....

bisimoto.com rules

DJ_SaNdOz

Bisi is a good friend to have, that guys brain is so incredibly cool

S@nt0s

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by DJ_SaNdOz &raquo;</TD></TR><TR><TD CLASS="quote">Bisi is a good friend to have, that guys brain is so incredibly cool </TD></TR></TABLE>


that is very thru.. when him and me get into a convo u need a recorder.. LOL

0Bisimoto

I am glad you like it, Santos. The one I sent you was a prototype...expensive, but a good one nonetheless. As you may see, my name was spelled "Bismoto" instead of "Bisimoto". That has been remedied. I have a whole line of high end apparel on the site: http://www.bisimoto.com

Put it this way...yours may be worth something huge one day...

Thanks for all the kind words, and support, guys..and gals!

92BluEH-3

omg im so buying something from you dude love the shirt hope to order one after xmas time

Turbo_y8

yea that is a tight shirt

S@nt0s

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Bisimoto &raquo;</TD></TR><TR><TD CLASS="quote">I am glad you like it, Santos. The one I sent you was a prototype...expensive, but a good one nonetheless. As you may see, my name was spelled "Bismoto" instead of "Bisimoto". That has been remedied. I have a whole line of high end apparel on the site: http://www.bisimoto.com

Put it this way...yours may be worth something huge one day...

Thanks for all the kind words, and support, guys..and gals!</TD></TR></TABLE>

HAHAHAHA I JUST NOTICED THAT NOW THAT U MENSTIONED IT.. TOO FUNNY.. EITHER WAY IM ROCKING IT LIKE NO OTHER .. LETTING THEM KNOW HOW US 1 SLAMMERS DO!

EJ1 wilcox

That's a tight shirt! lol

I'm going to order one!!