Sharing information - 505HP 356TQ Stock Bottom LS
#1
Honda-Tech Member
Thread Starter
Join Date: Aug 2009
Location: Baton Rouge,Louisiana
Posts: 7,635
Likes: 0
Received 3 Likes
on
3 Posts
Sharing information - 505HP 356TQ Stock Bottom LS
Original thread : http://forum.ectune.com/viewtopic.php?t=2875
Big props to Bugermass and eCtune for shattering doubters
Stock bottom end, ported head with our regrind cams, 20G with ebay tubular manifold
@21 PSI on Q16.
Big props to Bugermass and eCtune for shattering doubters
Stock bottom end, ported head with our regrind cams, 20G with ebay tubular manifold
@21 PSI on Q16.
#5
Honda-Tech Member
Join Date: Jan 2005
Location: b00sting my D16s, SoWis, USA
Posts: 7,015
Likes: 0
Received 7 Likes
on
5 Posts
Re: Sharing information - 505HP 356TQ Stock Bottom LS
Wow, more amazing is the torque hasn't started dropping yet. It also appears to spool better than a vtec head would.
I like seeing people jumping for joy in the 380hp b16 thread, then first post indicating imminent failure here.
I like seeing people jumping for joy in the 380hp b16 thread, then first post indicating imminent failure here.
Trending Topics
#8
#9
Honda-Tech Member
Join Date: Jul 2007
Location: , USA
Posts: 346
Likes: 0
Received 0 Likes
on
0 Posts
Re: Sharing information - 505HP 356TQ Stock Bottom LS
These engine can and will make power...for a short period of time. I am not afriad to push a stock enngine on a dyno for a short period of time to see a high number....because thats all its going to do.
However, Good job. But do a pull on some good tires!
#10
Honda-Tech Member
Join Date: Sep 2004
Location: Pembroke Pines, FL, USA
Posts: 626
Likes: 0
Received 0 Likes
on
0 Posts
Re: Sharing information - 505HP 356TQ Stock Bottom LS
Early in the year I pushed B18a engine to 400whp, Just to see if it could take it. To say the least, It did....on street tires. Being burning out didn't get me anywhere. I through my 24.5in M/T's on and went down the road. First pull, went through first and second and saw a cop so I slowed down. Turned around, Second pull, 1-3 gears...made it into 3rd gear for about 1000rpms and......Boom. Rod let chunks of it come out my front bumper...nasty.
These engine can and will make power...for a short period of time. I am not afriad to push a stock enngine on a dyno for a short period of time to see a high number....because thats all its going to do.
However, Good job. But do a pull on some good tires!
These engine can and will make power...for a short period of time. I am not afriad to push a stock enngine on a dyno for a short period of time to see a high number....because thats all its going to do.
However, Good job. But do a pull on some good tires!
#11
Honda-Tech Member
Join Date: Jul 2007
Location: , USA
Posts: 346
Likes: 0
Received 0 Likes
on
0 Posts
Re: Sharing information - 505HP 356TQ Stock Bottom LS
The rest of the rods were bent/warped very badly after a complete teardown to see what the internals looked like. Two rods were shattered, meaning in peice's, one appeared to have broken the bolt and the other in chunks. The other two rods were warped into what looked like boomarang's. Either way, I have no doubt a good couple pulls will destroy any stock engine at this HP.
However, everyone is wrong....no one is always right. So please be the person to prove this wrong and run amazing times and lets see it hold together for multiple pass's.
Best of luck.
However, everyone is wrong....no one is always right. So please be the person to prove this wrong and run amazing times and lets see it hold together for multiple pass's.
Best of luck.
Thread
Thread Starter
Forum
Replies
Last Post