... need eprom burner for hondata... ideas?... ((dont wanna spend $$$ for pocket programmer))
04-15-2003, 04:30 PM
#1
Member
Thread Starter
Join Date: Aug 2002
Posts: 1,452
Likes: 0
Received 0 Likes
on
0 Posts
... need eprom burner for hondata... ideas?... ((dont wanna spend $$$ for pocket programmer))
... anyone know where i can get one assembled with software?... looking for something similar to the batronix setup... anyone?... lemme know... thanks...
04-15-2003, 07:58 PM
#4
Member
Thread Starter
Join Date: Aug 2002
Posts: 1,452
Likes: 0
Received 0 Likes
on
0 Posts
Re: ... need eprom burner for hondata... ideas?... (boosted hybrid)
thanks, i will keep these in mind... but i was actually hoping to find burner and software for ~$50...
anyone else?
thanks...
anyone else?
thanks...
04-15-2003, 08:35 PM
#5
Honda-Tech Member
Join Date: Aug 2002
Location: ashEVILle, NC, USSR
Posts: 4,417
Likes: 0
Received 0 Likes
on
0 Posts
Re: ... need eprom burner for hondata... ideas?... (1.8T_EG)
Message Trickturn from carolinahondas.com... he has three broken Transtronic/xtronics Pocket Pussies. They just need the published fix, and if he brings them to the meet this weekend like he should I can prolly fix one of them no charge if he wants to sell one to you.
04-16-2003, 12:11 PM
#6
Re: ... need eprom burner for hondata... ideas?... (J. Davis)
Going the batronix route is about 75-100 dollars cheaper. It gets the work done fine, but isn't as convenient since you have to assemble it and use software in addition to the rom editor to program it.
I bought my batronix for 55 shipped unassembled. The software for the batronix is about $25 dollars. Lastly you just need a power source for it, I just used two 9 volt batteries.
Lemme know if you are interested and I'll send you a link.
I bought my batronix for 55 shipped unassembled. The software for the batronix is about $25 dollars. Lastly you just need a power source for it, I just used two 9 volt batteries.
Lemme know if you are interested and I'll send you a link.
Trending Topics
04-16-2003, 03:27 PM
#8
Member
Thread Starter
Join Date: Aug 2002
Posts: 1,452
Likes: 0
Received 0 Likes
on
0 Posts
Re: ... need eprom burner for hondata... ideas?... (J. Davis)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by J. Davis »</TD></TR><TR><TD CLASS="quote">Message Trickturn from carolinahondas.com... </TD></TR></TABLE>
i just sent him an email... thanks for the info... also, if you talk to him, lemme know if you here anything... thanks again...
i just sent him an email... thanks for the info... also, if you talk to him, lemme know if you here anything... thanks again...
04-16-2003, 05:45 PM
#9
Re: ... need eprom burner for hondata... ideas?... (Ivan)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Ivan »</TD></TR><TR><TD CLASS="quote">well on their website it says you can buy an assembled one.</TD></TR></TABLE>
I think it's 30 for assembly which brings it up to85 shipped plus software and stuff and you are saving only 50 bucks or less. After that I'd rather just pay extra since you have a case for the pocket programmer and the rom editor supports it natively
I think it's 30 for assembly which brings it up to85 shipped plus software and stuff and you are saving only 50 bucks or less. After that I'd rather just pay extra since you have a case for the pocket programmer and the rom editor supports it natively
Thread
Thread Starter
Forum
Replies
Last Post
VegasInvasion
Engine Management and Tuning
2
03-05-2010 09:58 PM
PrecisionH23a
Forced Induction
11
08-18-2005 03:50 PM
