mRvYbEs PYR build thread
#129
Honda-Tech Member
Thread Starter
iTrader: (1)
Join Date: Feb 2002
Location: bRoOkLyN, NY, USA
Posts: 977
Likes: 0
Received 0 Likes
on
0 Posts
Re: mRvYbEs PYR build thread
Thanks
I had a set of JDM Recaros too but I had to get rid of them as they were too heavy for my previous car. You got an extra set of R seats for me?
This is not a magic show. lol.
Thanks, I see you're all Spooned up now !!!!!!!!
Thanks. More updates are on the way
Thanks, I see you're all Spooned up now !!!!!!!!
Thanks. More updates are on the way
#133
Honda-Tech Member
Thread Starter
iTrader: (1)
Join Date: Feb 2002
Location: bRoOkLyN, NY, USA
Posts: 977
Likes: 0
Received 0 Likes
on
0 Posts
Re: mRvYbEs PYR build thread
I picked this up a while back to put on my RS but, never did so now it's going on the R. Just a quick test fit of my gurney flap.
Last edited by mRvYbEs; 05-20-2011 at 11:58 AM.
#136
Honda-Tech Member
Join Date: Jun 2006
Location: down the street,bythe river in the van, co, united states
Posts: 836
Likes: 0
Received 0 Likes
on
0 Posts
Re: mRvYbEs PYR build thread
dam reallly nice come up on that R!!
wish i could get my hands on a clean titile R like that mang
good luck keep us posted when you get it running and stuff
wish i could get my hands on a clean titile R like that mang
good luck keep us posted when you get it running and stuff
#137
Honda-Tech Member
Thread Starter
iTrader: (1)
Join Date: Feb 2002
Location: bRoOkLyN, NY, USA
Posts: 977
Likes: 0
Received 0 Likes
on
0 Posts
Re: mRvYbEs PYR build thread
Ok, ok. I’ll post a few.
So my good friend Mr Powerfulperformance decided to stop by and give a helping hand with Sunshine. This is his daily beater. Sorry the flash didn’t come on.
This guy is too cool. Always willing to wrench. You betta watch your finger and that hammer OG. lol
First, he pre-drills the holes with the spot weld remover
He then, uses a pry bar to loosen the bracket
Here we go with the hammer again !!!!!!!
After a half hour of hammering. prying and sweating, it’s finally off
After removal & before prep for K-Swap bracket
Glad you like it Mike.
Thanks bro. More updates to come
So my good friend Mr Powerfulperformance decided to stop by and give a helping hand with Sunshine. This is his daily beater. Sorry the flash didn’t come on.
This guy is too cool. Always willing to wrench. You betta watch your finger and that hammer OG. lol
First, he pre-drills the holes with the spot weld remover
He then, uses a pry bar to loosen the bracket
Here we go with the hammer again !!!!!!!
After a half hour of hammering. prying and sweating, it’s finally off
After removal & before prep for K-Swap bracket
Glad you like it Mike.
Thanks bro. More updates to come
Last edited by mRvYbEs; 05-20-2011 at 12:04 PM.
#149
Honda-Tech Member
Join Date: May 2006
Location: Abbeville/Lafayette, LA, USA
Posts: 1,163
Likes: 0
Received 0 Likes
on
0 Posts
Re: mRvYbEs PYR build thread
looking great man..in for updates...everytime i see a nice R build makes me wish i could afford to do one...
keep it up and be sure to take lots of pics...
keep it up and be sure to take lots of pics...