Gsr bearings in b16
#1
Honda-Tech Member
Thread Starter
Join Date: Oct 2007
Location: las vegas, nevada, clark
Posts: 644
Likes: 0
Received 1 Like
on
1 Post
Gsr bearings in b16
Would be safe to run one half of a gsr bearing along with one half of an b16 bearing in one Rod journal?
I know the gsr is much slimmer but still seats into place on the Rod cap. I ordered red bearings for my motor from Honda and they gave me gsr reds.
I know the gsr is much slimmer but still seats into place on the Rod cap. I ordered red bearings for my motor from Honda and they gave me gsr reds.
#4
Honda-Tech Member
Thread Starter
Join Date: Oct 2007
Location: las vegas, nevada, clark
Posts: 644
Likes: 0
Received 1 Like
on
1 Post
Re: Gsr bearings in b16
Ya, could you please explain, i searched the whole web, not one thing on it.
Ive taking apart a few gsr's and they had, acl std bearings in them. Not slim ones like oem. They were the normal width ones. I dont see why they cant be vise versa, if acls, or any other aftermarket will fit a gsr, and b16 ect..??
Ive taking apart a few gsr's and they had, acl std bearings in them. Not slim ones like oem. They were the normal width ones. I dont see why they cant be vise versa, if acls, or any other aftermarket will fit a gsr, and b16 ect..??
#5
Honda-Tech Member
Re: Gsr bearings in b16
b16 rods are like ls gsr are way smaller you will have too much of a gap and you will get low oil pressure and youll spin a bearing thus messing up the crank
#6
Honda-Tech Member
Thread Starter
Join Date: Oct 2007
Location: las vegas, nevada, clark
Posts: 644
Likes: 0
Received 1 Like
on
1 Post
Re: Gsr bearings in b16
im using the b16 rods. im only using 1 gsr half bearing, all clearances are .0015 so its all good on the oil pressure. i dont know what your trying to say..
Trending Topics
#8
Honda-Tech Member
Re: Gsr bearings in b16
exactly sorry didnt mean oil clearance issue i was speaking about a side to side clearance issue. The oil clearance is good though i woudn't recomend it but its actaully your motor but is it really worth taking a chance for 30 to 40 dollars your best bet is to order another set of bearings and play it safe cause itll cost you more in the long run
#9
Honda-Tech Member
Thread Starter
Join Date: Oct 2007
Location: las vegas, nevada, clark
Posts: 644
Likes: 0
Received 1 Like
on
1 Post
Re: Gsr bearings in b16
exactly sorry didnt mean oil clearance issue i was speaking about a side to side clearance issue. The oil clearance is good though i woudn't recomend it but its actaully your motor but is it really worth taking a chance for 30 to 40 dollars your best bet is to order another set of bearings and play it safe cause itll cost you more in the long run
Also if the slimmer bearings are sufficient for a gsr motor, why wouldn't it be for a b16? It is only 1 half, i dont think it would be too drastic?? Also oil squirters? Also here is the weird part, the acl standard box says for a b16, b18a b18b, ect.. and also a B18c...Now these are fat acls, why would larger acls work for a gsr but not vise versa?
#10
Honda-Tech Member
Re: Gsr bearings in b16
i'm looking at the acl catalog now, and they have different part numbers for the rod bearings between motors. b series mains are all the same though.
there's no way it would work as it sits anyway, since the tangs on the gsr rod bearings are on the wrong side.
there's no way it would work as it sits anyway, since the tangs on the gsr rod bearings are on the wrong side.
Thread
Thread Starter
Forum
Replies
Last Post