Throw-out bearing in need of greasing....
#1
Honda-Tech Member
Thread Starter
Join Date: Nov 2001
Location: previously 95redLUDE
Posts: 1,561
Likes: 0
Received 0 Likes
on
0 Posts
Throw-out bearing in need of greasing....
My car recently started to make a chirping noise that goes away when the clutch pedal is depressed. I've come to realize that its the thowout bearing in the clutch assembly. My question for you guys is, what should I use to grease this? What things do I need to look out for when opening up the clutch assembly? Roughly, how long should this take myself and one other person? I've got the Helms so guide me, but personal experience would be appreciated. Thanks.
#4
Honda-Tech Member
Thread Starter
Join Date: Nov 2001
Location: previously 95redLUDE
Posts: 1,561
Likes: 0
Received 0 Likes
on
0 Posts
Re: Throw-out bearing in need of greasing.... (Cottonwoodz)
Did you just get a clutch installed?
#5
Honda-Tech Member
Re: Throw-out bearing in need of greasing.... (95redLUDE)
High Temp wheel bearing grease works good
Even if he does put in a new one, the new one would still need to be greased too. Either way, a good greasing is called for.
[Modified by hot_EG, 1:21 AM 10/21/2002]
Even if he does put in a new one, the new one would still need to be greased too. Either way, a good greasing is called for.
[Modified by hot_EG, 1:21 AM 10/21/2002]
#6
Member
Join Date: Dec 2000
Location: Monroeville, PA, USA
Posts: 1,881
Likes: 0
Received 0 Likes
on
0 Posts
Re: Throw-out bearing in need of greasing.... (hot_EG)
WHAT-throwout bearings are not greased in the field. They are either good or need replaced. We are talking about the bearing-not the fork or linkage here.
As was asked-did you just replace the clutch and not the bearing If so that iis your problem. You will have to take the tranny out to fix this.
As was asked-did you just replace the clutch and not the bearing If so that iis your problem. You will have to take the tranny out to fix this.
#7
Re: Throw-out bearing in need of greasing.... (jc836)
greasing the throw out bearing is just a temporary solution. you can however grease a new one before putting it in.
but either way, a new one is in order.
but either way, a new one is in order.
Trending Topics
#8
Honda-Tech Member
Join Date: Jul 2002
Location: Columbia, Beaufort,, SC, USA
Posts: 3,603
Likes: 0
Received 0 Likes
on
0 Posts
Re: Throw-out bearing in need of greasing.... (bgod)
dont grease the surface that hits the clutch! just the pilot shaft. if u hear it its time for a new throw out. its only 40 dollars man
#9
Join Date: Aug 2002
Location: Calgary, Alberta, Canada
Posts: 43
Likes: 0
Received 0 Likes
on
0 Posts
Re: Throw-out bearing in need of greasing.... (BoostedH23a1)
After you change it out, something to keep in mind: You can prevent wear on the throwout bearing if you don't leave the clutch pedal pushed down while you're waiting for long lights, etc.
#10
Honda-Tech Member
Thread Starter
Join Date: Nov 2001
Location: previously 95redLUDE
Posts: 1,561
Likes: 0
Received 0 Likes
on
0 Posts
Re: Throw-out bearing in need of greasing.... (95redLUDE)
Like I said, I did just get the clutch replaced but I bet it is the same bearing. If it's making the noise then most likely it needs to be replaced, is that what you guys are saying? Does anyone have the part number by any chance? Thanks a lot for your replies, but how difficult is it to remove the tranny?
Thread
Thread Starter
Forum
Replies
Last Post
redman223
Honda Civic / Del Sol (1992 - 2000)
7
03-01-2024 01:55 PM