Honda-Tech - Honda Forum Discussion

Notices
 
Page 1 of 2
1
2
Search: Posts Made By: mem94043
Showing results 1 to 25 of 31
Search took 0.19 seconds.
Forum: Honda Accord (1990 - 2002)
08-14-2012, 11:06 AM
Replies: 2
Views: 1,061
Posted By mem94043

Fuel Pump removal frustration

Can't figure out how to get electrical lead off fuel pump (attached to sender unit) so I can slide tank out from under car. Rubber boot on electrical connection appears glued or something and I am...
Forum: Honda Accord (1990 - 2002)
06-22-2012, 09:50 PM
Replies: 5
Views: 6,399
Posted By mem94043

Re: Another way to test bad fuel pump?

Thanks for your reply. I dont have the adapter that's why I didnt try to mesaure with my fuel pressure guage. But, since I am not even gettig a 'squirt', I think its safe to say I have VERY LOW to...
Forum: Honda Accord (1990 - 2002)
06-19-2012, 07:59 AM
Replies: 5
Views: 6,399
Posted By mem94043

Another way to test bad fuel pump?

My 95 Accord LX has me stumped. It cranks well but never turns over. I suspect maybe no fuel or bad main relay. I am wondering if the test I just conducted (below) is a way to tell if it IS the pump....
Forum: Honda Accord (1990 - 2002)
05-10-2012, 12:18 PM
Replies: 4
Views: 1,342
Posted By mem94043

95 LX cranking but wont start - listen 2 link

Recently finished a head rebuild on my 95 Accord LX (see my other posts) and car ran for GREAT for 10 minutes or so then died. Car wouldn't re-start unless I let it sit overnight. Then it would only...
Forum: For Sale
03-28-2012, 07:18 PM
Replies: 0
Views: 300
Posted By mem94043

Time-Sert #4800 For Sale $320

I have a Time-Sert Universal Kit #4800 that I am planing on putting on Ebay but thought I woud give my fellows Honda enthusiasts first shot.

I used this kit to SAVE my 95 Accord LX 2.2L block. I...
Forum: Honda Accord (1990 - 2002)
03-25-2012, 08:10 PM
Replies: 2
Views: 1,386
Posted By mem94043

Cam wasn't seized after all

See my earlier post for the history on this... https://honda-tech.com/forums/showthread.php?t=3038431

Thought I had seized the cam (on my 95 Accord LX) but today I removed the valve cover only to...
Forum: Honda Accord (1990 - 2002)
03-20-2012, 07:38 AM
Replies: 5
Views: 7,010
Posted By mem94043

Re: Did I partially or almost seize my engine!??

Well, I'm toast! I think cam seized.

I bought the oil pressure gauge and hooked it up. (BTW, thanks Honda, could you make getting to the oil pressure switch any HARDER! Had to by a 24mm deep...
Forum: Honda Accord (1990 - 2002)
03-19-2012, 08:11 AM
Replies: 5
Views: 7,010
Posted By mem94043

Re: Did I partially or almost seize my engine!??

Thanks for your reply.

I am going to pickup an oil pressure gauge today and test. IF the oil pressure is GOOD, got any other thoughts on what it could be? BTW, the cylinder shop replaced 2 of my...
Forum: Honda Accord (1990 - 2002)
03-18-2012, 06:36 PM
Replies: 5
Views: 7,010
Posted By mem94043

Did I partially or almost seize my engine!??

I just finished getting my 95 Accord LX back together this weekend. It had a failed water pump several months ago and I tore it down to replace the WPump, TBelt, tensioners, seals, etc. I sent the...
Forum: Honda Accord (1990 - 2002)
03-03-2012, 12:12 PM
Replies: 3
Views: 10,399
Posted By mem94043

How 2 remove injectors from fuel rail?

I have both the OEM and Chilton shop manuals for my 95 Accord LX. It is not clear how to remove injector from fuel rail. I want to replace rubber bits.

Do they just pull out? Are they threaded...
Forum: Want to Buy
02-27-2012, 09:50 AM
Replies: 3
Views: 848
Posted By mem94043

Re: WTB Time-Sert #1812 M8 x 1.25

Thanks for reply blueGTS.

I am thinking about Helicoil if I cant find a TS kit cuz they ARE cheap in price comparison. However, you can't beat a Time-Sert insert for strength.

Were you able to...
Forum: Want to Buy
02-26-2012, 03:03 PM
Replies: 3
Views: 848
Posted By mem94043

WTB Time-Sert #1812 M8 x 1.25

Looking to buy (or rent) Time-Sert kit model 1812. Need to repair stripped stud hole on cylinder head (exhaust side) of F22B2. I think it's M8 x 1.25
Forum: Honda Accord (1990 - 2002)
02-21-2012, 08:56 PM
Replies: 6
Views: 2,654
Posted By mem94043

Re: CAN'T REMOVE inner pulley!! HELP!

Got it off!! Took oneprblmcat's advice since I was already leaning in that direction. I slowly and lightly heated the gear with propane torch, being careful to try and not heat the shaft. I then took...
Forum: Honda Accord (1990 - 2002)
02-19-2012, 01:18 PM
Replies: 1
Views: 847
Posted By mem94043

TBelt Adj arm locking bolt stays in or out?

Finishing up a timing belt change on a 95 Accord LX coupe (non-vtec) and having doubts about locking bolt on timing belt adjustment arm...

Chilton's says on Accords (all but VTEC), the locking...
Forum: Honda Accord (1990 - 2002)
01-30-2012, 08:08 PM
Replies: 6
Views: 2,654
Posted By mem94043

CAN'T REMOVE inner pulley!! HELP!

Can anyone PLEASE tell me how to get the dang inner pulley off? I am so close to giving up on changing the main seal on my 95 Accord LX.

I cant get the pulley off. I can't get the key off the...
Forum: Honda Accord (1990 - 2002)
01-16-2012, 09:17 AM
Replies: 1
Views: 647
Posted By mem94043

3rd crankshaft pulley STUCK?

Hey there Accord gurus,

Anyone have any tips on getting the last pulley (right before the front crankshaft seal) loose?? I have PB Blasted the heck outta mine but it won't budge. I've also heavily...
Forum: Honda Accord (1990 - 2002)
11-02-2011, 10:15 AM
Replies: 1
Views: 618
Posted By mem94043

P/Steering, gas pedal mods possible on 95 LX?

Just got my 95 Accord LX a few months ago and there are 2 things that kinda bug me (compared to my previous car) and would like to know if any of you Accord Gurus have come up with any Mods...

1....
Forum: Honda Accord (1990 - 2002)
11-02-2011, 09:14 AM
Replies: 0
Views: 569
Posted By mem94043

Dumb question about CylHd alignment pins

I had to take a couple month break during my top-end rebuild on my 95 Accord LX (lack of $$$) and forgot which holes the cylinder head alignment dowels go into. I know they go in the corners but...
Forum: Honda Accord (1990 - 2002)
10-11-2011, 11:02 AM
Replies: 2
Views: 2,965
Posted By mem94043

95 Accord/LX head bolts re-usable or T2Y?

Hi Accord gurus,

I am re-assembling the top end on a used 95 Accord I bought.

Question: Are the head bolts re-usable or are they Torque-to-Yield (throw away). I would assume they are re-usable...
Forum: Honda Accord (1990 - 2002)
07-16-2011, 12:35 PM
Replies: 2
Views: 1,236
Posted By mem94043

Shoot, rolled a new camshaft seal!

Hi there Accord gurus,

Anyone have an opinion about how a camshaft seal should be installed?

I am in the process of putting my 95 Accord LX top-end back together. I started to put the cam back...
Forum: Honda Accord (1990 - 2002)
07-04-2011, 12:47 PM
Replies: 2
Views: 641
Posted By mem94043

Where do these SLEEVES go???

Hi Accord gurus,

Got my cylinder head back last week and to my surprise the shop didn't put it all back together. Shop owner said he thought I would want to put camshaft seal in myself. Uh, no, I...
Forum: Honda Accord (1990 - 2002)
06-26-2011, 12:27 PM
Replies: 3
Views: 6,420
Posted By mem94043

Replacing cylinder head bolts

I recently read somewhere that you should replace the cylinder head bolts when doing a 'head gasket' job. Last week I picked up my F22B2 head (pressure test and valve job) and the shop owner said I...
Forum: Honda Accord (1990 - 2002)
05-15-2011, 10:54 AM
Replies: 3
Views: 12,082
Posted By mem94043

Can't remove lower Timing belt cover!...

Damn you lower timing belt cover!

How the hell does this thing come out? I have the engine mount removed but this cover won't slide up and out, nor out through the bottom of engine compartment.
...
Forum: Honda Accord (1990 - 2002)
05-07-2011, 09:02 AM
Replies: 7
Views: 18,250
Posted By mem94043

Crank Pulley thread normal, right?

OK, this is my first timing belt job on my recently purchased 95 Accord (or any Accord). I am trying to remove the crank pulley bolt but this SUCKER IS REALLY STUCK. No previous car has ever defeated...
Forum: Northern California
03-24-2011, 10:49 AM
Replies: 0
Views: 767
Posted By mem94043

411 on Cylinder Heads Unlimited in Santa Clara , CA?

I am thinking of having the head done on my 95 Accord LX coupe and was wondering if any members here have done business with Dave over at Cylinder Heads Unlimited in Santa Clara, CA

Thanks for any...
Showing results 1 to 25 of 31
 
Page 1 of 2
1
2


 
Forum Jump


All times are GMT -8. The time now is 07:50 PM.