Honda-Tech - Honda Forum Discussion

Notices
Search: Posts Made By: bstadictd
Showing results 1 to 15 of 15
Search took 0.35 seconds.
Forum: All Motor / Naturally Aspirated
09-11-2012, 09:33 AM
Replies: 30
Views: 2,466
Posted By bstadictd

Re: how do you put together the motor with custom made parts?

Fall in love with engines (hondas), build a lot of them and begin to understand the limits of the parts then bam custom parts will be made. Very valid point to understand '' engine assembler vs...
Forum: Hybrid / Engine Swaps
01-05-2012, 11:55 AM
Replies: 13
Views: 33,580
Posted By bstadictd

Re: GSR head on B20B JDM high comp motor.

retard the timing for more clearance. you can also measure clearance with a dial gauge. use soft springs from a hardware store and use the dial gauge to measure how far you can push the valve open...
Forum: Hybrid / Engine Swaps
01-05-2012, 10:52 AM
Replies: 13
Views: 33,580
Posted By bstadictd

Re: GSR head on B20B JDM high comp motor.

retarding or decreasing timing moves the power band higher into the revs and advancing or increasing will mover the power band lower into the revs.
Forum: Hybrid / Engine Swaps
01-05-2012, 07:28 AM
Replies: 13
Views: 33,580
Posted By bstadictd

Re: GSR head on B20B JDM high comp motor.

that should be considered, but you will need to use degree wheels to find out where to set everything. you will also still need to measure your running clearance. you can guess and check but...
Forum: Hybrid / Engine Swaps
01-04-2012, 05:24 PM
Replies: 13
Views: 33,580
Posted By bstadictd

Re: GSR head on B20B JDM high comp motor.

my buddy ran into clearance issues on a b20z with b16 head(stock cams).you could also get a set of rs machine pistons with the correct valve reliefs. i have also heard the work and doesn't work...
Forum: Hybrid / Engine Swaps
01-04-2012, 04:43 PM
Replies: 13
Views: 33,580
Posted By bstadictd

Re: GSR head on B20B JDM high comp motor.

i run gsr cams with a b16 head on a stock b20b. has 20k miles no problems. the way i understand it is that clearance issues are more common with the z block not the b. you could always clay bar the...
Forum: Tech / Misc
03-27-2009, 10:55 AM
Replies: 8
Views: 657
Posted By bstadictd

Re: gauge cluster temp gauge?

thanks for the help. i will be replacing the whole cluster with one from the junk yard and probably the dimmer switch also
Forum: Tech / Misc
03-26-2009, 01:42 PM
Replies: 8
Views: 657
Posted By bstadictd

Re: gauge cluster temp gauge?

so far i have tested the temp sensor i got 77 omhs the engine probably wasnt all the way warm didnt drive it just let it run for a few. as i was testing it the omhs slowly went down like i should if...
Forum: Tech / Misc
03-25-2009, 08:56 PM
Replies: 8
Views: 657
Posted By bstadictd

Re: gauge cluster temp gauge?

92 civic si
Forum: Tech / Misc
03-25-2009, 02:33 PM
Replies: 8
Views: 657
Posted By bstadictd

Icon2 gauge cluster temp gauge?

temp gauge goes right to "H" right on start up and the gauge cluster doesnt light up. i have been trying to locate all of the grounds hoping to find one disconnected.I have also replaced the temp...
Forum: Transmission & Drivetrain
03-10-2009, 10:00 PM
Replies: 5
Views: 1,230
Posted By bstadictd

Re: intermediate shaft and axle for eg

lsd would be nice. i thought that there might be an intermediate shaft that would work with my tranny and motor cause the z6 block looks like it has the bolt holes on it for the intermediate shaft....
Forum: Forced Induction
03-10-2009, 09:47 PM
Replies: 14,627
Views: 2,513,891
Posted By bstadictd

Re: SOHC Boosted Set ups! Chime IN...a place for the SINGLE SLAMS

92 si civic
d16z6 stock block
race egineering block gaurd
.02 over 9:1 ross pistons
probe rods
comp cam 59300
comp springs
aem cam gear
slight hand port z6 head
edelbrock preformer inake...
Forum: Transmission & Drivetrain
03-10-2009, 09:01 PM
Replies: 5
Views: 1,230
Posted By bstadictd

Re: intermediate shaft and axle for eg

what about the old d series intagras and the zc engines that have equal length axles? its boosted on 15 pounds it makes ok power thats why it torq steers. there is nothing wrong with the suspension.
Forum: Transmission & Drivetrain
03-10-2009, 11:14 AM
Replies: 5
Views: 1,230
Posted By bstadictd

intermediate shaft and axle for eg

from what car do i need to get the intermediate shaft and axle from to put in my 92 civic with a d16z6? trying to get rid of a little torq steer.
Forum: Honda Civic / Del Sol (1992 - 2000)
01-14-2009, 11:08 AM
Replies: 3
Views: 1,662
Posted By bstadictd

Re: 59300 cam install. wheres the vtec?

i also have the 59300 cam and comp springs in my motor and it doesnt crossover. if it does it gets stuck in vtec and idles like ass. i also tried building a new head with my same cam and springs same...
Showing results 1 to 15 of 15


 
Forum Jump


All times are GMT -8. The time now is 11:22 PM.