Honda-Tech - Honda Forum Discussion

Notices
 
Page 1 of 20
1
2
3
11
Last »
Search: Posts Made By: uberEFtuner
Showing results 1 to 25 of 494
Search took 0.93 seconds.
Forum: Honda CRX / EF Civic (1988 - 1991)
10-04-2016, 03:14 PM
Replies: 0
Views: 603
Posted By uberEFtuner

Help 88 rear disc swap, mount holes, bleeding brakes

I did a rear disc brake swap in the past. this time my brakes wont bleed on one side. I swapped the 40/40 prop valve,the problem swapped to the other side. WTF?

Also the rear sway bar install. I...
Forum: Tech / Misc
01-03-2016, 05:40 PM
Replies: 10
Views: 4,516
Posted By uberEFtuner

Re: oem fabric adhesive vs aftermarket.

You are using too much glue. Or the wrong kind of glue Or not waiting long enough for it to tack up long enough.

You want a glue that sprays out like spider webs. Touch it to see if it has...
Forum: Honda CRX / EF Civic (1988 - 1991)
01-01-2016, 03:14 PM
Replies: 3
Views: 2,219
Posted By uberEFtuner

Re: Rear main seal help

They sell a seal puller at advance auto. Or drill a small hole and put a drywall screw in then pull with your favorite plyers. Just be sure not to scratch the crank shaft.
Forum: Welding / Fabrication
01-01-2016, 02:37 PM
Replies: 9
Views: 1,055
Posted By uberEFtuner

Re: Make universal cat direct fit?

Just get a test cat off ebay, cut off the fake cat and weld in a real one. I used a magniflow.
Forum: Tech / Misc
01-01-2016, 02:31 PM
Replies: 10
Views: 4,516
Posted By uberEFtuner

Re: oem fabric adhesive vs aftermarket.

I use the permatex from autozone in the orange can about $12. Spray both headliner and new fabric. Wait 10 min for it to tack up and press hard. I use foam backed headliner fabric from...
Forum: Tech / Misc
11-17-2015, 08:14 AM
Replies: 5
Views: 7,921
Posted By uberEFtuner

Re: Seeking simple solution to make civic car doors open wider (90+ degree opening)

You could also remove the interior door panel. That will give you some room.
Forum: Audio / Security / Video
11-17-2015, 08:10 AM
Replies: 6
Views: 2,585
Posted By uberEFtuner

Re: Sound deadening

Watch some youtube videos on how to install the stuff. You only need it where the metal is thin and will vibrate. Putting blanket of dynamat is a waste of time and will add 200lbs. You DO want...
Forum: Audio / Security / Video
11-17-2015, 08:06 AM
Replies: 23
Views: 5,650
Posted By uberEFtuner

Re: EG Custom Sub Enclosure install? Anyone done it?

Where are you located? I am in Pennsylvania. I have done fiberglass enclosures. It is the only way to fit a sub into a corner nice and tight. I have pics of one i did I will have to post a how...
Forum: Honda Accord (1990 - 2002)
09-24-2015, 06:34 AM
Replies: 4
Views: 855
Posted By uberEFtuner

Re: Engine swap and 5spd swap NO SPARK

Got it running!!! Used a 1992 distributor then ran wires to the plug for the crank sensors by the timing belt. Almost all the colors matched up except the ones for the crank sensor. But I looked...
Forum: Honda Accord (1990 - 2002)
09-15-2015, 05:37 AM
Replies: 4
Views: 855
Posted By uberEFtuner

Re: Engine swap and 5spd swap NO SPARK

The ground is attached to the intake. The distributor is original and is the internal coil type. I have 12 volts at the coil. Also when I scan the ecu it comes up with no fault codes. I do have...
Forum: Honda Accord (1990 - 2002)
09-13-2015, 10:19 AM
Replies: 4
Views: 855
Posted By uberEFtuner

Engine swap and 5spd swap NO SPARK

I have a 1997 Odyssey had f22b7 with auto. Swapped in a F22a6 with the wiring from the old engine and distributor. The ECU is from a 1996 accord 5 speed. This is just being used to Run it for now...
Forum: Honda CRX / EF Civic (1988 - 1991)
04-22-2015, 10:35 AM
Replies: 3
Views: 1,591
Posted By uberEFtuner

Re: 89 hatchback interior panel removal help plz

Did you check the tail lights? The foam seals are known to leak
Forum: Tech / Misc
04-22-2015, 10:30 AM
Replies: 2
Views: 1,433
Posted By uberEFtuner

Re: Help me identify this exhaust

It looks like 1994-1997 Accord but without the crappy flex pipe.
Forum: Audio / Security / Video
02-23-2015, 01:10 PM
Replies: 11
Views: 7,749
Posted By uberEFtuner

Re: OEM Gathers Subwoofer: Options to replace 40W, 1ohm speaker

I have a speaker for you! Its EXACTLY the same part number. It came from a Subaru. Its a panasonic unit but the woofer has the same part number.
Forum: Honda Accord (1990 - 2002)
02-08-2015, 05:47 PM
Replies: 7
Views: 3,662
Posted By uberEFtuner

Re: 95 Accord Trans Problem (Hidden Bolt)

If you are very careful about not setting things on fire you could use a propane torch. You want to put the torch on there for 15min and get it warm...NOT HOT. Just slowly warm up the area where...
Forum: Honda Accord (1990 - 2002)
02-08-2015, 04:46 PM
Replies: 3
Views: 5,489
Posted By uberEFtuner

Re: Installed new PS rack. Now bubbles

Its very simple. You have an air leak somewhere between the reservoir and the pump. When the pump sucks fluid from the tube with a hole in it air is sucked into the tube because air is thinner...
Forum: Honda Accord (1990 - 2002)
02-01-2015, 10:39 AM
Replies: 0
Views: 9,813
Posted By uberEFtuner

f22a6 rebuild, I need torque specs

I am rebuiding an f22a6. I have a Chilton manual that has the following specs.
rod bearing bolts: 34 ft/lbs i assume they mean connecting rods?
main bearing bolts: 52 ft/lbs

Just want to know...
Forum: Honda Minivans, Crossovers, and Trucks
01-16-2015, 05:45 PM
Replies: 0
Views: 1,249
Posted By uberEFtuner

2005 odyssey EXL j35 VCM, P0301-p0306 missfire

So If you own a J series(j35) here is some info for you. The whole van shook at idle and the engine with the hood popped sounded like a diesel when cold.
The car was throwing...
Forum: Honda Accord (1990 - 2002)
12-14-2014, 10:43 AM
Replies: 2
Views: 2,685
Posted By uberEFtuner

rebuilding f22a6 need crank bearing clearances

I am slowly rebuilding a f22ay, the block has been honed and decked. I have king crank bearings and I need to know the clearances. This was a perfectly good running engine with 160K on it. I just...
Forum: Honda CRX / EF Civic (1988 - 1991)
10-04-2014, 06:43 PM
Replies: 879
Views: 242,672
Posted By uberEFtuner

F/S 1990-1991 hatchback door cards, needs repaint, Bethlehem,PA 18017

F/S 1990-1991 Civic hatchback door cards, needs repaint. These are in need of some work, but all of the hard work has been done. Bethlehem,PA 18017
Forum: Honda CRX / EF Civic (1988 - 1991)
09-25-2014, 02:22 PM
Replies: 8
Views: 7,306
Posted By uberEFtuner

Re: USDM mirrors on JDM Power Folding Mirrors for CRX

You can probably swap the glass, but be warned that the plastic clips will probably break.
Forum: Honda Accord (1990 - 2002)
09-25-2014, 02:13 PM
Replies: 8
Views: 1,091
Posted By uberEFtuner

Re: 4th Gen OEM muffler fit 5th Gen?

NOPE! I already tried it. I found a catback cheap for a 5th gen and bought it for parts when I had a 4th gen. The curves are all wrong, Including the bend for the rear to clear the suspension.
Forum: Welding / Fabrication
09-15-2014, 06:51 PM
Replies: 27
Views: 11,871
Posted By uberEFtuner

Re: Cad Database???

back from the dead HA HA!!!! I am interested in keeping this thread going. I have a semester of Solidworks 2014 under my belt.

I wish I had access to the software again. wink wink!;)

I do...
Forum: Honda Accord (1990 - 2002)
08-28-2014, 06:50 AM
Replies: 2
Views: 629
Posted By uberEFtuner

Re: Help interpreting results of compression test

Do the compression test again. But this time remove the valve in the compression tester. Then watch how fast each cylinder loses pressure. If it has a burnt valve it will leak out very quickly. ...
Forum: Honda Minivans, Crossovers, and Trucks
08-04-2014, 04:52 PM
Replies: 1
Views: 1,051
Posted By uberEFtuner

05 odyssey EXL front strut clicking? consumable parts

I have a 2005 Odyssey EXL that has a click from the drivers side when it hits a bump. I have inspected all of the suspension components. I have also tried to rock the vehicle to replicate the...
Showing results 1 to 25 of 494
 
Page 1 of 20
1
2
3
11
Last »


 
Forum Jump


All times are GMT -8. The time now is 09:43 PM.