Honda-Tech - Honda Forum Discussion

Notices
 
Page 1 of 17
1
2
3
11
Last »
Search: Posts Made By: B18C4-T
Showing results 1 to 25 of 413
Search took 1.36 seconds.
Forum: Acura Integra
11-05-2014, 07:10 AM
Replies: 15
Views: 1,287
Posted By B18C4-T

Re: 94 Integra GSR won't turn on

The clutch safety switch on your friends car may be bypassed. Look under your dash at the top of the clutch peddle and see if the connector there is connected to the switch. If it is then disconnect...
Forum: Acura Integra
03-25-2014, 11:55 AM
Replies: 3
Views: 1,624
Posted By B18C4-T

Where is this engine from??

I'm rebuilding an Integra with my son for his 16th birthday. I ordered a B18C1 that is supposed to be JDM, but it has a lot of surface rust and the serial number on the block is 1700003 which doesn't...
Forum: Forced Induction
07-31-2013, 04:02 PM
Replies: 23
Views: 6,745
Posted By B18C4-T

Re: Fuel injectors not working

The noid light showed they are recieving a signal. When I put a 9v battery on one it didn't do anything. I'm going to send them all out to be tested and cleaned.
Forum: Forced Induction
07-31-2013, 12:50 PM
Replies: 23
Views: 6,745
Posted By B18C4-T

Re: Fuel injectors not working

I'm going to pick up a noid light on my way home so I can make sure they are getting a signal.

The car sat for a month or so in the trailer then wouldn't start. Before that it always fired right...
Forum: Forced Induction
07-31-2013, 08:52 AM
Replies: 23
Views: 6,745
Posted By B18C4-T

I swapped the ecu for one out of my other car.

I swapped the ecu for one out of my other car.
Forum: Forced Induction
07-30-2013, 05:55 PM
Replies: 23
Views: 6,745
Posted By B18C4-T

Originally I checked the injectors with the plug...

Originally I checked the injectors with the plug connected and got 12v across both wires. I just pulled the injector clips and I have 12v on one wire and nothing on the other one.

I also...
Forum: Forced Induction
07-30-2013, 09:04 AM
Replies: 23
Views: 6,745
Posted By B18C4-T

Re: Fuel injectors not working

I replaced my fuel pressure gauge on the fuel rail and verified that I still have 60 psi when the pump is on.
Forum: Forced Induction
07-30-2013, 06:00 AM
Replies: 23
Views: 6,745
Posted By B18C4-T

Re: Fuel injectors not working

To the top
Forum: Forced Induction
07-29-2013, 05:13 PM
Replies: 23
Views: 6,745
Posted By B18C4-T

Re: Fuel injectors not working

Msd 96lb injectors and 93 octane fuel
Forum: Forced Induction
07-29-2013, 05:04 PM
Replies: 23
Views: 6,745
Posted By B18C4-T

Re: Fuel injectors not working

I am using a resistor box, I have 12v at both wires on all the injectors.
Forum: Forced Induction
07-29-2013, 04:11 PM
Replies: 23
Views: 6,745
Posted By B18C4-T

Re: Fuel injectors not working

Oh yeah, I replaced the main relay as well.
Forum: Forced Induction
07-29-2013, 03:25 PM
Replies: 23
Views: 6,745
Posted By B18C4-T

Re: Fuel injectors not working

I'm running a switch to the pump, no relay. The pump is definitely running.
Forum: Forced Induction
07-29-2013, 02:25 PM
Replies: 23
Views: 6,745
Posted By B18C4-T

Icon2 Fuel injectors not working

I'm running an Aeromotive A1000 fuel pump/filter/regulator and have 60 psi at the fuel rail, which is what Tony set it at when he tuned the car. The car will not start and I don't even get a fuel...
Forum: All Motor / Naturally Aspirated
05-30-2013, 08:03 AM
Replies: 19
Views: 4,065
Posted By B18C4-T

Re: Found metal pieces in the oil pan

They are not magnetic. I was the last person to lock the cams when I did the timing belt and nothing broke, bent but not broke.

I'm trying to decided whether to tear the motor all the way down and...
Forum: All Motor / Naturally Aspirated
05-29-2013, 11:02 AM
Replies: 19
Views: 4,065
Posted By B18C4-T

Re: Found metal pieces in the oil pan

I'll have to check and see if I still have the distributor that locked up with this motor and see if it is the pin out of that. Thanks!
Forum: All Motor / Naturally Aspirated
05-29-2013, 04:06 AM
Replies: 19
Views: 4,065
Posted By B18C4-T

Re: Found metal pieces in the oil pan

If they were ring lands they wouldn't be round, these look like retaining pins of some sort.
Forum: All Motor / Naturally Aspirated
05-29-2013, 04:04 AM
Replies: 19
Views: 4,065
Posted By B18C4-T

Re: Found metal pieces in the oil pan

They are metal pieces, the distributor keys are more square. I thought of those as well because I had a distributor lock up, but then realized that was the old engine. Here are some more pics, I'm...
Forum: All Motor / Naturally Aspirated
05-28-2013, 11:44 AM
Replies: 19
Views: 4,065
Posted By B18C4-T

Re: Found metal pieces in the oil pan

Ok, I'll try that when I get home tonight.

Thank you
Forum: All Motor / Naturally Aspirated
05-26-2013, 09:54 AM
Replies: 19
Views: 4,065
Posted By B18C4-T

Re: Found metal pieces in the oil pan

Both pieces have a broken end on them, but the broken ends don't seem to fit together. They're round, not square like the keyway.
Forum: All Motor / Naturally Aspirated
05-26-2013, 08:32 AM
Replies: 19
Views: 4,065
Posted By B18C4-T

Found metal pieces in the oil pan

So I was changing the oil pan gasket on a B16A and found these two metal pieces in my oil pan. The car was running well before this. I put it back together and drove it home and parked it. This...
Forum: Drag Racing
02-06-2007, 06:38 PM
Replies: 62
Views: 8,725
Posted By B18C4-T

Re: POLL: Your SFWD build cost? (TurboJesse)

I'm probably around 45-50k at this point with all the different setups I've done. I still don't have a clean pass and need to finish some small stuff on the car. I always tell people that the car is...
Forum: Drag Racing
01-16-2007, 10:43 PM
Replies: 2
Views: 738
Posted By B18C4-T

Re: where to buy fuel sump kit.. (yaaj1320)

I believe Competition Engineering has them, I know http://www.full-race.com has them. I just had one made when my car was at the fabricators. Larry
Forum: Drag Racing
12-15-2006, 07:32 PM
Replies: 11
Views: 979
Posted By B18C4-T

Re: how important is having solid doors? (97grnrs)

On a street driven car I wouldn't gut the doors. On a track car I only would if I had a cage. If you get broadsided the you have no protection. I have a 12 point cage and still have factory doors....
Forum: Drag Racing
12-05-2006, 08:39 AM
Replies: 329
Views: 22,166
Posted By B18C4-T

Re: (MLRtimestl)

I'm in for a couple. Damn this came as a surprise. Larry
Forum: Forced Induction
11-30-2006, 07:13 PM
Replies: 43
Views: 3,959
Posted By B18C4-T

Re: (Skeletor!)

Here is mine. I miss it. I moved to Hawaii and stored it at home because they closed the track here. Let me see if this works.
https://img86.imageshack.us/img86/5339/civicyf8.th.jpg...
Showing results 1 to 25 of 413
 
Page 1 of 17
1
2
3
11
Last »


 
Forum Jump


All times are GMT -8. The time now is 04:53 PM.