When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Damn that turbo puts down some power! Just ordered my Reaper with the 74mm turbine wheel and T4 0.68 A/R housing. I'm in Idaho now, but Nayr will be tuning my car once it's put together. The guys at CoRaceFab are awesome.
Carlos was telling me last night at the meet someone was getting the same turbo with that wheel lol.
Well this happen last night.... lol. Thinking valve end gave out or something.. Possibly stock cast guides now that I am using vtec. New GSC valve train coming in and oil pump, turbo rods, pistons, bearings, etc etc. Picked up a new head today.
Crank is not damaged same with all bearings. Sleeves are good also. Still going too a turbo tough manley rod and new set of Honda bearings and a acl high performance oil pump. Exhaust wheel and compressor wheel look great. Hope the GSC valves,retainers,springs,guides,seals, work out for me lol. Going to do ferrea valve locks/keepers. Clutch still has some life on it.
The tips of thrust washers are rough like sand paper. Not sure what thats about. I am happy to get the block O-ringed and get some speedfactory L19 head studs so I can move on with the coolant issue.
Yes 5280ft. It sounds completely different with vtec. Tuner said we could get 760 ish out of it if we cared about the number. Its a safe tune because I beat on it. He loves you shoden lol. You told turbo me I should max around 700 at my elevation and I was happy at 636. He already had the high and low maps set so we ran without vtec and got 600 (to make sure I wasn't full of ****) and then we plugged it in and the first run was 734 with 11.5 afrs. And we called it good lol. The cams are the magic lol.
You running the GSC T1's as on your initial build list right ? After months of deliberation I ordered a set of T1's which should arrive soon. I'm at 5500ft elevation so your results give me some hope.
I'll be trying to max out my Holset HX40 (69 lb/min) with the new cams so hoping to reach ~ 680whp before upgrading to a 67mm wheel.
Yea the GSC t1 cams. I am getting a 4 piston outlaw cylinder head and going to bump the compression to 11.5. Also going to run a 1.06 a/r exhaust housing. Should be rolling again in couple months :D
Yea the GSC t1 cams. I am getting a 4 piston outlaw cylinder head and going to bump the compression to 11.5. Also going to run a 1.06 a/r exhaust housing. Should be rolling again in couple months :D
Jesus that's some pretty high compression. Very curious how that turns out, should help with low end torque and spool. The tune will have to be spot on though, and you'll need to be using some prim-o fuel.
Jesus that's some pretty high compression. Very curious how that turns out, should help with low end torque and spool. The tune will have to be spot on though, and you'll need to be using some prim-o fuel.
Not as high as Muckman's 13.5:1 compression GSC T1 Integra. 11.5:1 isn't that bad..
Well time for an update. I finally got my new Terminator turbo from the GODS at STC in and my 4 piston cylinder head/ Skunk 2 Race manifold along with new 3" out/in double backdoor intercooler. Plan to assemble bottom end this weekend with new turbo tuff rods, Speedfactory spec outlaw/arias pistons, Honda bearings, ACL oil pump, Speedfactory L19 headstuds, and JE pro seal head gasket. I also had the block oringed this time with copper wire from GE. Then I am taking it to CORaceFab to get my cams degreed and my vtv and ptv clearances checked. Didn't do a cam degree 1st time. I guess ill shoot for 950WHP? (734whp was just fine also lol) I just need to order a Weldon fuel pump. I only really run this on the street so I can only get lower 700whp down (witch is scary as hell lol). I have a set of slicks this year so ill get to see how much better its gets. Once my cage goes in and my DSS axles come in it will run down the 1/4. I also changed out to a Speedfactory tucked -AN cooling system.
nice build! I think the coolant issue u were having its mines too. waiting on my ge gasket and springs and retainers to come in to do all that along with itr oil pump and gates race belt and just got a new radiator ordered. sorry to see about the boom. cant wait to see it back up.
Little update. Car made 841whp at 26 psi 75% duty cylce on E98. We decided to stop because I am on Hondata and AEM infinity system being installed this week. Makes 600whp at 13 psi witch is gate pressure. New stuff: Weldon 2345-A fuel pump with controller, 10 point cage, seats, harnesses, dss 5.9 axles, boost activated exhaust cutout. Going to add a smaller spring when I install my AEM system and cam trigger setup. 600hp on gate is way too much. STC TERMINATOR!!!
Little update. Car made 841whp at 26 psi 75% duty cylce on E98. We decided to stop because I am on Hondata and AEM infinity system being installed this week. Makes 600whp at 13 psi witch is gate pressure. New stuff: Weldon 2345-A fuel pump with controller, 10 point cage, seats, harnesses, dss 5.9 axles, boost activated exhaust cutout. Going to add a smaller spring when I install my AEM system and cam trigger setup. 600hp on gate is way too much. STC TERMINATOR!!!
08-08-2016, 11:11 AM
re: Titan101's GSR 2.0L Interceptor / Terminator Build Expansion
