damndan23

i hav been wondering about this also.. my setup is basicaly the same except myne is 83mm benson sleeves.with a walbro feeding a bosch 044 to ID1000s ..GT35/82R made 509/298 with 93oct @17psi... a buddy told me to set enrichment @ 300 and -5 and and play with the timing for mor or less boost my activation starts @ 6500 to 6700. im only making a few psi off the line. is there a timing to fuel ratio. i cant figure out why my 2step doesnt pop n kackle im still learning how to navigat the S300 so any usefull tips are welcome

sgnlab

You can make as much as full boost just need to play with the timing to get it right. Remember your adding 400 units of fuel you need it because launch limiter makes alot of heat in the engine. I love the way it sounds make sure to set vtec MPH to zero!

sgnlab

try -35 on the timing retard.

turbo-crx

can you do this with crome also?

dester223

I'm serious. I was a 82x89 engine so it bogged bad unless the car came out on 25 pounds.

But it ran 9.97. 9.95 and 9.85 back to back to back pretty much the first time out without any problems.

Seemed to do OK for me.

sgnlab

nope

dester223

Well, you COULD. But it takes a little bit of playing around in the map to get it to work.

sgnlab

if you say so! Why ask then???

boosted k20

Yes you sure can. In crome GOLD, there is a working 2-step function similiar to S300 where you can pull timing and add fuel.

if you want to do it w/o crome gold u will need to modify the low cam fuel maps to add fuel/take out timing. u will need to have VTEC working on speed so u wont have VTEC at all at idle (dont disable VTEC speed check in the options menu). then u need to set ur 2-step activation point higher than what ur VTEC rpm is now go into ur low cam timing map and run -6* timing from 0" to whatever the max boost limit is on the map and also a few hundred rpms below and above the 2-step activation rpm. (i.e. if ur vtec is set at 4.4K rpms, and ur 2-step point is set to 6.5K go into the low cam ign map and run -6* from 5000 and up). now add like 10% more fuel into the same areas where u just set timingto -6*. Most important, make sure u add in the timing script fix into your crome map that will alow ur car to run below 15*. if u dont do this u wont get good results. for P30 maps hit CTRL+K and enter this: _rom_fill(0×58e6, 0×590d, 0×00); _rom_fill(0×6a99, 0×6ac0, 0×00);

this is what it should look like

damndan23

ok...even tho im not tryin to push that much boost off the line i tried it anyway and ended up with the same results... . anymore ideas?

dester223

I wasn't the one that asked. But boostedk20 pretty much explained how you could.

I just responded with you COULD do it.....???
-Chuong

miller

Something is wrong there. I bet I know what is wrong

V-SPEC 1

What do you think is wrong miller?

sgnlab

Its not the wand that makes the magic, its the magician

sgnlab

set vtec speed to zero

dester223

Also, you have to sit on the 2 step for "a little bit" for it to build boost. I see a lot of my customers with little seat time just go up there, let it bounce off the 2 step twice, not build any boost then bog.

You gotta get on the 2 step and see the boost go up. Sometimes it can take more than a couple pops.
-Chuong

jdmek922

i no this is super old but i had to ask. i just want to shot some sweet *** flames. what yall thing i need to put it at to do it. lol

DC2Mex

I have mine at 600 fuel enrichment and -45 ignition timing and activation at 6400 to 6800.

DA 4 Lyfe

600 fuel? Seems a little unnecessary to me...

Steeve_Civic

Fuel 10
Ignition -25
Lauch 7100

Duende

bump this, i have been having trouble launching my s366 on my new set up,

Natural Aspirations

Tips:
Set Vtec Engagment Speed to 0
S300 Fuel is in Table values
KPRO Fuel is in Percentage
You cannot typically build more boost than WG pressure, boost control is not active.

SPOOLINmatt

the s300 launch control/"anti lag" feature doesnt seem to be nearly as aggressive as it used to be. I want to find an old version to play with to see really.

"S300 Fuel is in Table values" are you for SERIAL?

DA 4 Lyfe

^X2

Natural Aspirations

Pretty sure, it works completely different in KPro.

It's less harsh due to the settings, you can adjust