Honda-Tech - Honda Forum Discussion
This is as far as I got with it.
This is as far as I got with it.
0 2017/10/03 05:47:07
Might try to sell this setup.
Might try to sell this setup.
0 2017/10/06 14:29:32
0 2017/10/06 14:29:38
These four wires powered the fans
These four wires powered the fans
0 2017/10/06 14:29:42
Spliced into these two, which ran to the switch inside
Spliced into these two, which ran to the switch inside
0 2017/10/06 14:29:46
Blue wires go to power and ground, white and black go to fans.
Blue wires go to power and ground, white and black go to fans.
0 2017/10/06 14:29:51
0 2017/10/06 14:36:02
0 2017/10/06 14:36:07
0 2017/10/06 14:36:12
0 2017/10/06 14:36:16
0 2017/10/06 14:36:19
Got everything out of the way to get the turbo off (radiator, wg and dumptube, downpipe, etc. ). Also will be getting Skunk 2 half radiator and spal fan when I reassemble everything.
Got everything out of the way to get the turbo off (radiator, wg and dumptube, downpipe, etc. ). Also will be getting Skunk 2 half radiator and spal fan when I reassemble everything.
0 2017/10/06 14:40:08
Turbo ready to be sent out for a rebuild :thumbup:
Turbo ready to be sent out for a rebuild :thumbup:
0 2017/10/06 14:40:12
Started remounting my gauges. Didn't get too far since the wiring was a mess. Unfortunately I'll have to extend two of the harnesses to reach up to here.
Started remounting my gauges. Didn't get too far since the wiring was a mess. Unfortunately I'll have to extend two of the harnesses to reach up to here.
0 2017/10/06 14:40:15
Gauge wiring pulled out.
Gauge wiring pulled out.
0 2017/10/06 14:40:20
0 2017/10/06 18:37:45
0 2017/10/06 18:37:52
0 2017/10/06 18:37:59
0 2017/10/06 18:45:19
0 2017/10/06 18:45:27
0 2017/10/06 18:45:34
0 2017/10/06 18:45:41
0 2017/10/06 18:45:49
0 2017/10/06 18:52:16
0 2017/10/06 18:52:21
0 2017/10/14 15:57:08
0 2017/10/15 10:36:22
0 2017/10/15 10:36:28
0 2017/10/15 10:36:35
0 2017/10/15 10:36:40
0 2017/10/15 10:36:45
0 2017/10/15 10:36:51
0 2017/10/15 10:36:57
Inducer roughly 2"
Inducer roughly 2"
0 2017/10/20 03:25:37
Exducer 2.75"ish
Exducer 2.75"ish
0 2017/10/20 03:25:41
0 2017/10/20 03:25:44
Had a number on the back
Had a number on the back
0 2017/10/20 03:25:49
Does this look alright?
Does this look alright?
0 2017/10/20 03:25:52
0 2017/10/20 12:26:02
0 2017/11/02 18:57:27