Honda-Tech - Honda Forum Discussion
Next - secure the shroud to the projector.
Next - secure the shroud to the projector.
0 2023/05/12 16:22:21
I used fishing line - hard to see!
I used fishing line - hard to see!
0 2023/05/12 16:22:26
Finished securing the halo to the shroud.
Finished securing the halo to the shroud.
0 2023/05/12 16:22:34
I clearanced the shroud for the halo wiring.
I clearanced the shroud for the halo wiring.
0 2023/05/12 16:22:40
I drilled 3 holes for the halo mounts.
I drilled 3 holes for the halo mounts.
0 2023/05/12 16:22:45
Finished w/ the mods to halo.
Finished w/ the mods to halo.
0 2023/05/12 16:22:53
Coil is removed in this picture, ignitor remains in place (lower right of picture).
Coil is removed in this picture, ignitor remains in place (lower right of picture).
0 2023/05/13 09:02:28
Free the wiring harness from the holder.
Free the wiring harness from the holder.
0 2023/05/13 09:02:39
Remove the coil tower.
Remove the coil tower.
0 2023/05/13 09:02:49
0 2023/05/13 09:10:03
Gently pry off w/ screwdrivers.
Gently pry off w/ screwdrivers.
0 2023/05/13 09:13:47
18 cm
18 cm
0 2023/05/13 09:13:53
Measure the install depth of the counterweight.
Measure the install depth of the counterweight.
0 2023/05/13 09:14:01
Now the shaft slides out of the housing - note the old seal.
Now the shaft slides out of the housing - note the old seal.
0 2023/05/13 09:17:57
Keep track of the ignitor connections!
Keep track of the ignitor connections!
0 2023/05/13 09:18:06
A close up of the pickup
A close up of the pickup
0 2023/05/13 09:18:12
Remove the bearing retainer.
Remove the bearing retainer.
0 2023/05/13 09:21:41
I placed the bearing plate on some pieces of wood and tapped the shaft out.
I placed the bearing plate on some pieces of wood and tapped the shaft out.
0 2023/05/13 09:21:52
41 cm, just under.
41 cm, just under.
0 2023/05/13 09:21:58
Measure the install depth.
Measure the install depth.
0 2023/05/13 09:22:07
0 2023/05/13 09:26:26
0 2023/05/13 09:26:31
0 2023/05/13 09:26:36
0 2023/05/13 09:26:41
0 2023/05/13 09:26:46
0 2023/05/16 08:06:25
Looking at this pic, I should remove the Phillips fasteners that are no longer needed. I would hate for them to come loose and interfere with the brights.
Looking at this pic, I should remove the Phillips fasteners that are no longer needed. I would hate for them to come loose and interfere with the brights.
0 2023/05/16 08:48:17
Trying to level the projectors.
Trying to level the projectors.
0 2023/05/18 10:05:50
0 2023/05/18 10:05:59
Less than 13mm
Less than 13mm
0 2023/05/27 14:02:28
Old bearing:
Old bearing:
0 2023/05/27 14:02:34
0 2023/05/29 04:41:46
Oh noes!
Oh noes!
0 2023/06/07 07:11:10
Don't spread your supports out this wide:
Don't spread your supports out this wide:
0 2023/06/07 07:11:19
Confirm your install depth.
Confirm your install depth.
0 2023/06/07 07:13:23
Put your supports in nice and close to center - under the raised lip.
Put your supports in nice and close to center - under the raised lip.
0 2023/06/07 07:13:30
The spring side of the seal goes towards the engine and oil.
The spring side of the seal goes towards the engine and oil.
0 2023/06/07 07:15:53
Claw the old seal out:
Claw the old seal out:
0 2023/06/07 07:16:02
The crack in the plate is tightened up:
The crack in the plate is tightened up:
0 2023/06/07 07:18:41
Test fit the cracked bearing plate in the housing.
Test fit the cracked bearing plate in the housing.
0 2023/06/07 07:18:49