Honda-Tech - Honda Forum Discussion
Blox Spacer gets it super close
Blox Spacer gets it super close
0 2017/09/26 12:47:51
2 Blox spacers... Perfect fit
2 Blox spacers... Perfect fit
0 2017/09/26 12:47:52
0 2017/09/26 12:47:53
0 2017/09/26 12:47:54
0 2017/09/26 12:47:56
0 2017/09/26 12:47:57
0 2017/09/26 12:47:57
0 2017/09/26 12:47:58
Zip Tied off until I move forward with the swap. I need to plug the fitting so it doesn't get any crud inside
Zip Tied off until I move forward with the swap. I need to plug the fitting so it doesn't get any crud inside
0 2017/09/26 12:47:59
Here is the wiper mechanism with the cover removed. takes 3 bolts to remove it.
Here is the wiper mechanism with the cover removed. takes 3 bolts to remove it.
0 2017/09/26 12:48:00
Wiper mechanism removed
Wiper mechanism removed
0 2017/09/26 12:48:01
Took a few tried to find the optimal position for the hole, I couldn't find any good references online. This seemed to be a good position.
Took a few tried to find the optimal position for the hole, I couldn't find any good references online. This seemed to be a good position.
0 2017/09/26 12:48:03
5/8ths plate I got at home depot, 99 cents each
5/8ths plate I got at home depot, 99 cents each
0 2017/09/26 12:48:04
Very sturdy
Very sturdy
0 2017/09/26 12:48:04
Upper mount reinforcement
Upper mount reinforcement
0 2017/09/26 12:48:05
Upper mount from a better angle.
Upper mount from a better angle.
0 2017/09/26 12:48:07
I added 3 more plates between the firewall and pedal mount so things would be very sturdy.
I added 3 more plates between the firewall and pedal mount so things would be very sturdy.
0 2017/09/26 12:48:08
Cutout for master
Cutout for master
0 2017/09/26 13:08:55
Blox Spacer
Blox Spacer
0 2017/09/26 13:08:57
Blox Spacer fitment with pedal
Blox Spacer fitment with pedal
0 2017/09/26 13:08:58
Using this as a template to drill the holes
Using this as a template to drill the holes
0 2017/09/26 13:08:59
Test Fitment of the pedal to check the angle
Test Fitment of the pedal to check the angle
0 2017/09/26 13:08:59
Drill bit I used
Drill bit I used
0 2017/09/26 13:09:02
Drill bit compared with Master
Drill bit compared with Master
0 2017/09/26 13:09:03
S2000 AP1 Blox Master cyl
S2000 AP1 Blox Master cyl
0 2017/09/26 13:09:04
Master cyl set up poorly as I had it in the accord.
Master cyl set up poorly as I had it in the accord.
0 2017/09/26 13:09:05
0 2017/09/26 13:09:06
Top is S2000 and bottom is Accord/Prelude push rod
Top is S2000 and bottom is Accord/Prelude push rod
0 2017/09/26 13:09:07
First hole drilled
First hole drilled
0 2017/09/26 13:09:08
Spacer as template
Spacer as template
0 2017/09/26 13:09:09
After test fit I had to adjust the angle a bit
After test fit I had to adjust the angle a bit
0 2017/09/26 13:09:10
Second hole drilled and secured for center hole
Second hole drilled and secured for center hole
0 2017/09/26 13:09:11
Center hole drilled.
Center hole drilled.
0 2017/09/26 13:09:12
Master mounted temporarily to test fitment
Master mounted temporarily to test fitment
0 2017/09/26 13:09:14
Primary install of the pedal
Primary install of the pedal
0 2017/09/26 13:09:15
Had to add a second Spacer for properly spacing the push rod
Had to add a second Spacer for properly spacing the push rod
0 2017/09/26 13:09:16
Pedal position
Pedal position
0 2017/09/26 13:09:17
With 2 spacers there was not much extra threads but it should be ok
With 2 spacers there was not much extra threads but it should be ok
0 2017/09/26 13:09:18
0 2017/09/26 13:09:19
0 2017/09/26 13:09:20