Honda-Tech - Honda Forum Discussion
View from the front. There's one area with a slight gap, I cut the circle with a sawzall so it was kind of hectic. If I had it to do over (I actually intended to do this but got distracted with work and life garbage so forgot. I would have cut the top and bottom long so I could make triangle bend at the top and bottom, so those wings would meet up with the bend at the end. Might just cut out a thin rectangle, cut that diagonally then use those as stand offs.
View from the front. There's one area with a slight gap, I cut the circle with a sawzall so it was kind of hectic. If I had it to do over (I actually intended to do this but got distracted with work and life garbage so forgot. I would have cut the top and bottom long so I could make triangle bend at the top and bottom, so those wings would meet up with the bend at the end. Might just cut out a thin rectangle, cut that diagonally then use those as stand offs.
0 2020/10/25 15:09:33
Maybe 2mm clearance, might end up getting a 2row radiator instead of the 3 row.
Maybe 2mm clearance, might end up getting a 2row radiator instead of the 3 row.
0 2020/10/25 18:52:37
As it sits.
As it sits.
0 2020/10/25 18:56:10
Offset coupler
Offset coupler
0 2020/11/04 20:28:38
0 2020/11/04 20:30:12
Almost there
Almost there
0 2020/11/04 20:31:05
Picked up a turbo blanket too.
Picked up a turbo blanket too.
0 2020/11/06 10:02:15
Marked a line with calipers, got a notch started with a hack saw blade, then let it rip with the sawzall.
Marked a line with calipers, got a notch started with a hack saw blade, then let it rip with the sawzall.
0 2020/11/07 11:11:58
Had to do a lot of filing and it's still not even. Should seal fine, I'll use a little gasket maker along with the paper gasket.
Had to do a lot of filing and it's still not even. Should seal fine, I'll use a little gasket maker along with the paper gasket.
0 2020/11/07 11:12:21
0 2020/11/07 19:03:29
0 2020/11/07 19:03:48
As it sits.
As it sits.
0 2020/11/15 13:36:13
Out with the old in with the new. Have the extra set too.
Out with the old in with the new. Have the extra set too.
0 2020/11/16 19:54:29
Big wind storms last night and a dead branch from God knows where managed to knock off my mirror trim. It popped back on after some fiddling. A few light scratches.
Big wind storms last night and a dead branch from God knows where managed to knock off my mirror trim. It popped back on after some fiddling. A few light scratches.
0 2020/11/16 19:55:34
0 2020/11/21 18:49:54
0 2020/11/21 18:50:36
0 2020/11/29 22:53:37
0 2020/11/29 22:53:56
Old stock plastic top
Old stock plastic top
0 2020/12/04 10:34:42
New aluminum shift pattern indicator.
New aluminum shift pattern indicator.
0 2020/12/04 10:35:13
Close up
Close up
0 2020/12/04 10:35:59
0 2020/12/04 16:10:41
0 2020/12/13 21:00:31
0 2020/12/13 21:00:58
0 2021/10/04 19:02:55
0 2021/10/08 20:20:08
0 2021/10/20 19:06:59
0 2021/10/20 19:07:40
0 2021/10/23 15:53:18
0 2021/10/29 10:56:19
3k yellow setting on the switch back LED low beams.
3k yellow setting on the switch back LED low beams.
0 2021/11/16 20:20:34
6k setting on the LEDs, they match the LED running lights really well.
6k setting on the LEDs, they match the LED running lights really well.
0 2021/11/16 20:21:11
I liked them so much I ordered the LED interior lights, they're insane, you could barely see inside the car before with the lights on. They're uncomfortably bright now. Like genuinely jarring.
I liked them so much I ordered the LED interior lights, they're insane, you could barely see inside the car before with the lights on. They're uncomfortably bright now. Like genuinely jarring.
0 2021/11/16 20:22:37
Also installed them in the city lights sockets in my SDM lights. They're bright AF, I had hyper white standard bulbs before and you could barely see they were on... These are crazy bright.
Also installed them in the city lights sockets in my SDM lights. They're bright AF, I had hyper white standard bulbs before and you could barely see they were on... These are crazy bright.
0 2021/11/16 20:24:24
Here's the top of the stock evaporator, I didn't take pictures of all the leaves inside, it was bad lol, and I had previously pulled a bunch out when I pulled the blower motor a year or two ago. Like two dust pans FULL.
Here's the top of the stock evaporator, I didn't take pictures of all the leaves inside, it was bad lol, and I had previously pulled a bunch out when I pulled the blower motor a year or two ago. Like two dust pans FULL.
0 2021/11/16 20:26:17
Almost forgot. I got a rivnut kit, and wrinkle blacked the coil mounting bracket and got that mounted permanently. It was held in with screws straight into the metal before.
Almost forgot. I got a rivnut kit, and wrinkle blacked the coil mounting bracket and got that mounted permanently. It was held in with screws straight into the metal before.
0 2021/11/16 20:28:04
0 2021/11/18 11:21:43
Upper half of the blower motor.
Upper half of the blower motor.
0 2021/11/18 11:22:50
Rusted backing plate. This is sadly the 'after' picture lol
Rusted backing plate. This is sadly the 'after' picture lol
0 2021/11/18 11:23:37
Was pretty gross when it showed up.
Was pretty gross when it showed up.
0 2021/11/18 11:24:35