Honda-Tech - Honda Forum Discussion
0 2020/01/21 19:25:29
0 2020/01/21 19:25:57
0 2020/01/21 19:26:26
0 2020/06/28 09:53:33
0 2020/06/28 09:54:08
0 2020/07/03 11:17:03
0 2020/07/14 16:49:56
0 2020/07/20 16:53:30
0 2020/07/24 16:20:49
0 2020/07/25 15:29:30
0 2020/07/25 21:19:09
0 2020/07/25 21:19:40
Mfactory sandwich plate, autometer sending unit, autometer oil temp sensor, and the wire harness I made for them.
Mfactory sandwich plate, autometer sending unit, autometer oil temp sensor, and the wire harness I made for them.
0 2020/07/26 22:14:09
0 2020/07/26 22:14:32
0 2020/07/28 17:07:56
0 2020/07/28 17:09:02
After third wet coat, 4th including the dust coat.
After third wet coat, 4th including the dust coat.
0 2020/07/30 16:15:52
4th touch up coat hitting a few low spots and light coverage for the rest so it's even.
4th touch up coat hitting a few low spots and light coverage for the rest so it's even.
0 2020/07/30 16:17:29
Peeled the masking tape.
Peeled the masking tape.
0 2020/07/30 17:45:30
Protruding threads cut off prop valve. Used aluminum tape to protect the intake manifold.
Protruding threads cut off prop valve. Used aluminum tape to protect the intake manifold.
0 2020/08/14 16:34:07
Lower IACV ground down. I flattened it off a little more after this pic. Used aluminum tape again to protect the motor and plug.
Lower IACV ground down. I flattened it off a little more after this pic. Used aluminum tape again to protect the motor and plug.
0 2020/08/14 16:34:54
0 2020/08/15 21:04:51
Strain relief on analog inputs wire harness
Strain relief on analog inputs wire harness
0 2020/08/24 17:02:30
Removed resistors.
Removed resistors.
0 2020/08/24 17:03:30
All buttoned up again
All buttoned up again
0 2020/08/24 17:04:30
0 2020/08/30 16:24:17
0 2020/09/23 17:56:35
0 2020/10/10 21:08:27
0 2020/10/10 21:08:45
Clocked 38mm Tial WG. With push lock fittings installed.
Clocked 38mm Tial WG. With push lock fittings installed.
0 2020/10/13 21:24:29
Top view.
Top view.
0 2020/10/13 21:25:00
0 2020/10/13 21:26:20
2" to 2.5 inch hot side. Sneaks under the traction bar, it's all coupler under it so should be ok even if it bumps on something.
2" to 2.5 inch hot side. Sneaks under the traction bar, it's all coupler under it so should be ok even if it bumps on something.
0 2020/10/16 17:30:45
Scratched and coated intercooler piping, waste gate, and blow off valve.
Scratched and coated intercooler piping, waste gate, and blow off valve.
0 2020/10/17 20:25:35
Downpipe test fitting.
Downpipe test fitting.
0 2020/10/19 06:47:08
Cleaned up downpipe flange
Cleaned up downpipe flange
0 2020/10/24 21:21:46
Mounted turbo, buffed housings
Mounted turbo, buffed housings
0 2020/10/24 21:22:51
Oil drain, maybe maybe maybe.
Oil drain, maybe maybe maybe.
0 2020/10/24 21:23:04
Clamped these rails together, torched them till they melted the plastic on the seam. Made for a nice round over.
Clamped these rails together, torched them till they melted the plastic on the seam. Made for a nice round over.
0 2020/10/25 15:04:38
Drilled a bunch of the tiny mounting holes, used a bunch of little nuts bolts and washers to clamp the shroud to the fan. Used red locktite on the bolts.
Drilled a bunch of the tiny mounting holes, used a bunch of little nuts bolts and washers to clamp the shroud to the fan. Used red locktite on the bolts.
0 2020/10/25 15:07:00