TurboBumblBee

CAR IS SOLD!! MY BABY IS GONE, HOPEFULLY INTO GOOD HANDS... ILL MISS THE CAR ALOT, LOTS OF BLOOD, SWEET, AND TEARS!!

http://www.geocities.com/ryanekirk/index.htm

Details first, then pics
1993 Honda Civic DX hatch
Phoenix Yellow Paint 1.5 yrs old (always garaged)
Approx. 150k miles on shell
Approx. 8k miles on the built motor
385whp/270tq @ 19 psi pump gas
Should be well over 500whp on pump gas but I didn’t have anymore time on the dyno to run race gas.
Car is capable of running 11sec 1/4 miles runs.

Bottom End-
98 Integra GSR bottom end
AEBS t-sleeves
84mm (2.0 motor) bore
CP 9.1 low comp. pistons
Eagle rods
New OEM oil pump, OEM water pump, and OEM timing belt
Cometic 84mm Head gasket
ARP Head studs

Head-
Stock GSR head no internal head work done except AEM cam gears
ITR valve cover
Skunk2 Intake Manifold

Transmission-
96 Integra GSR tranny
Quiffe lsd
Honda mtf
Clutchmasters stage 4 clutch
Stock flywheel
NO GRIDS!!

Turbo Setup-
Drag turbo kit w/ many upgraded parts
Drag Exhaust Manifold
Tial wastegate
Drag intercooler
2.5" Drag downpipe
2.5" Apexi n1 cat-back exhaust (axle back muffler needs to be replaced soon, dented)
UPGRADED Precision SC44 turbo
Greddy Turbo timer
AR Fab Manual boost controller
Fast-turbo.com oil feed and drain kit
Vacuum manifold on firewall
Tuned to 19 psi turned and runs at 17psi daily on 93oct. pump gas

Fuel Setup-
Walbro 255 fuel pump
Inline pro fuel rail
Precision 680cc interjectors
Honda OEM resistor box
AEM FPR
Camp1320 autolink fuel pressure gauge
MSD Digital 6
Magnacore Wires

EMS-
Hondata s200b w/ 3step
Hondata p28 socketed ecu
GM 3bar map sensor

Suspension-
Entire Suspension was just replaced and installed and has less than 2000 miles on it, these new suspension parts include...
Integra GSR front and rear disc brake
RS booster and master cylinder
4040 prop valve
Axxis ultimate pads
Brembo rotors
Stainless steel brake lines
Omni-power full coilovers
Full-Race traction Bars

Wheels and tires-
Flat Black 15" Rota slipstreams
BFG Comp TA zr4 tires


Audio-
Alpine 7894(i think) head unit top of line 2 years ago
Polk MOMO (the good ones from last year) 6 3/4" components
Alpine 4 channel amp
Honda OEM Audio Console

Gauges-
Autometer tach and shift light
Autometer volt gauge
Autometer boost gauge
Autometer a/f ratio gauge
Autometer oil pressure gauge
Autometer EGT gauge
Gauges mounted in dash, I have a new dash to install that matches the doors


Misc. Stuff on or in car
C&R radiator and slim fan
Carbon Fiber hood
Integra GSR cloth seats
Orange Corner lights
Catz zeta hid kit
Silver Star headlights
Honda Civic EX full power doors
-including mirrors, windows, and locks!
Front and rear upper strut bars
Prothane Mount Inserts on ALL motor mounts
Viper 500esp car alarm

Extra Parts that will come with car
BFG drag radials 205/50/15 used w/ about 4k miles on them
Civic Black colored dash to replace current grey one
Rear Interior Panels (taken out to install roll cage but didn’t get that far)
JDM ITR rear sway bar w/ beaks kit
Stock hood painted Phoenix Yellow


http://www.geocities.com/ryanekirk/


Modified by TurboBumblBee at 10:34 PM 4/3/2005

VTECisSeXY

ian.

car price

TurboBumblBee

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by TurboBumblBee &raquo;</TD></TR><TR><TD CLASS="quote">im asking $15,000 right now but im sure i wont get that</TD></TR></TABLE>

Thanks man.. i know i probably wont get what i would like to get out of the car but it would be nice..

ian.

yeah man i hear ya but gL

TurboBumblBee

anyone interested..

91glassycrx

Hey man I noticed that u said u had a cage in it . Can u still get people in the back seat.

seros

u noticed wrong..read his post again

bump for a nice set up ...and i doubt ull part out but if u do holla

oh yeah who did ur boring and sleeving?
and who tuned it and where was it tuned at?

TurboBumblBee

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by 91glassycrx &raquo;</TD></TR><TR><TD CLASS="quote">Hey man I noticed that u said u had a cage in it . Can u still get people in the back seat.</TD></TR></TABLE>

cage was never purchased.. i was going to install one but never got around to it..


<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by 000s &raquo;</TD></TR><TR><TD CLASS="quote">u noticed wrong..read his post again

bump for a nice set up ...and i doubt ull part out but if u do holla

oh yeah who did ur boring and sleeving?
and who tuned it and where was it tuned at?
</TD></TR></TABLE>

what parts are you looking for?? if it comes down to it i will take certain parts off possibly..

Mike at northeast automachine in CT did the aebs sleeves for me and did a very nice job.

It has spent several hours on the dyno at AR Fabrication in Winchester, VA

seros

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by TurboBumblBee &raquo;</TD></TR><TR><TD CLASS="quote">

what parts are you looking for?? if it comes down to it i will take certain parts off possibly..

</TD></TR></TABLE>

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by TurboBumblBee &raquo;</TD></TR><TR><TD CLASS="quote">
-Hondata s200b w/ 3step Hondata p28 socketed ecu GM 3bar map sensor

-Full-Race traction Bars

-Axis/Lenso 13" slick wheels
MT 24x7.5x13" slicks
BFG drag radials
</TD></TR></TABLE>

HIGHLY intrested in the hondata... is that a s200b with boost option <U>and</U> 3-step option??

how much thread on the slicks?
and what rims are the drag radial on?

u can pm me a price on them and/or a cell number so we can chat about them


regarless bump 4u

TurboBumblBee

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by 000s &raquo;</TD></TR><TR><TD CLASS="quote">
HIGHLY intrested in the hondata... is that a s200b with boost option <U>and</U> 3-step option??

how much thread on the slicks?
and what rims are the drag radial on?

u can pm me a price on them and/or a cell number so we can chat about them

regarless bump 4u
</TD></TR></TABLE>

check your PM.. i would really like to keep the car complete how it is now specially the hondata because without that the car cant run correctly!

seros

yeah yeah i know but i neeeeeeed a hondata for my set up also sooo i though id ask

pmed u back

TurboBumblBee

ttt

TurboBumblBee

anyone out there looking for a car..

TurboBumblBee

MUST SELL!!

Bought a new car last night and i want to start parking the new car in the garage...

price lowered, make me an offer

this car is very nice...

TurboBumblBee

friday morning bump

TurboBumblBee

saturday bump

TurboBumblBee

early monday morning bump

TurboBumblBee

bump

TurboBumblBee

TTT

TurboBumblBee

TTT

need to sell this car.. i dont want to sell it but i have to...

litterbox

Bump for a dream car and a local seller.

TurboBumblBee

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by litterbox &raquo;</TD></TR><TR><TD CLASS="quote">Bump for a dream car and a local seller.</TD></TR></TABLE>

Thanks bro...

TurboBumblBee

bedtime bump...

TurboBumblBee

ttt

still for sale..