Acura Integra All Integra Except ITR

studdering problem around 4k please help!!!

Thread Tools
 
Search this Thread
 
Old Sep 2, 2004 | 06:28 PM
  #1  
integra94turbo's Avatar
Thread Starter
 
Joined: Jun 2004
Posts: 4
Likes: 0
From: dallas, tx, usa
Default studdering problem around 4k please help!!!

once i get around 4k and start boosting up my car studders bad in any gear, i can get the rpms up higher with no boost but once i start to boost it cuts out and back fires. i know that it is not my a/f cause i have the new aem wideband sensor and its reading a good a/f. once i put in a quaife lsd is when it started happening. i am not that good on all the sensor stuff and was wondering if anyone could help me on this one. also at what rpm does the 2nd set of butterflies on a stock gsr intake manifold come in?
Reply
Old Sep 3, 2004 | 03:38 PM
  #2  
integra94turbo's Avatar
Thread Starter
 
Joined: Jun 2004
Posts: 4
Likes: 0
From: dallas, tx, usa
Default Re: studdering problem around 4k please help!!! (integra94turbo)

anyone?
Reply
Old Sep 3, 2004 | 05:58 PM
  #3  
adrenaline-racing's Avatar
 
Joined: Nov 2003
Posts: 122
Likes: 0
From: Lawrence, Kansas, U.S.A.
Default Re: studdering problem around 4k please help!!! (integra94turbo)

Is your map sensor seeing the boost ? If it is mounted on top of the throttlebody you need to move it and block off the hole on top. Hook a vaccumm line before the turbo and hook it to the Map sensor.
Reply
Old Sep 4, 2004 | 02:01 PM
  #4  
integra94turbo's Avatar
Thread Starter
 
Joined: Jun 2004
Posts: 4
Likes: 0
From: dallas, tx, usa
Default Re: studdering problem around 4k please help!!! (integra94turbo)

OK i reset the ECU and retried to pull it up above 4k same problem when i check the ECU code it comes up with 21. I looked it up and it says its the VTEC controler i checked the voltage and its at 3.76v with the key on the on postion but not running. According to the manual your suposed to have ~12v with the key in the on position but not running. i checked with another ECU and got 11v but i had the same problem when i pull it up abopve 4k. i also traced that wire back to my ecu to see if it was a bad wire but i am getting the same voltage from there the 3.76v. if my problem is that i am not getting the 12v with the engine off is it because i have a bad ecu? what would fix my problem? If any one has any other sugestions please let me know and help is greatly apreciated.
Reply
Old Sep 4, 2004 | 02:47 PM
  #5  
XSrcing's Avatar
 
Joined: Feb 2002
Posts: 17
Likes: 0
From: Dallas, TX
Default

whats up chris, this is sean.

someday soon i will come over and we can swap parts (ECU, VTEC controller) between our cars to see what fixies it.
Reply
Old Sep 4, 2004 | 03:22 PM
  #6  
davejj40's Avatar
 
Joined: Aug 2004
Posts: 74
Likes: 0
From: San Francisco, Ca, USA
Default Re: (XSrcing)

wiring? it sounds like an ignition problem tho
Reply
Old Sep 5, 2004 | 01:44 AM
  #7  
integra94turbo's Avatar
Thread Starter
 
Joined: Jun 2004
Posts: 4
Likes: 0
From: dallas, tx, usa
Default Re: (XSrcing)

thanks, i was talking to someone today and said that since i dropped the trans i might not have gotten all the grounds bolted back down tight and to check those. would the speed sensor cause problems like this i read that it has some control over the injectors and thats the only sensor that was really messed with cause its on the tranny and all. let me know what you think
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
blackcrx16
Honda CRX / EF Civic (1988 - 1991)
25
Apr 14, 2006 06:35 AM
busakiller
Forced Induction
11
Jun 7, 2005 03:49 AM
lscivc
Honda Civic / Del Sol (1992 - 2000)
9
Feb 19, 2005 08:04 AM
kell211
Forced Induction
3
Oct 8, 2003 07:00 PM
420aNT
Forced Induction
4
Sep 21, 2003 05:02 PM




All times are GMT -8. The time now is 07:39 AM.