POST MODS HERE
#1
New User
Thread Starter
Join Date: Oct 2001
Location: san ramon, CA, USA
Posts: 8
Likes: 0
Received 0 Likes
on
0 Posts
POST MODS HERE
OK, it's official. The G5 civic hatch of some sort is gonna be my car. Because i didn't buy a delsol, that leaves me with some ca$h.
I have 6 grand, everthing from job to contests to scholarships i'm illicitly spending.
Post the mods you want, with the company and everything (IE. DC sport header, AEM cold air intake) and i will do them over the course of the year.
Oh and recommend an engine swap. i'm assuming 5 g can afford anyone of these:
B16 Si thingy
H22a prelude thingy
B18C(1 or 5) R thingy
Thanks a lot in advance.
I have 6 grand, everthing from job to contests to scholarships i'm illicitly spending.
Post the mods you want, with the company and everything (IE. DC sport header, AEM cold air intake) and i will do them over the course of the year.
Oh and recommend an engine swap. i'm assuming 5 g can afford anyone of these:
B16 Si thingy
H22a prelude thingy
B18C(1 or 5) R thingy
Thanks a lot in advance.
#2
I forgot more about hondas then you will ever know....
Join Date: Feb 2001
Location: hop,skip, and a jump from the city,, new friggin york, USA
Posts: 5,310
Likes: 0
Received 1 Like
on
1 Post
Re: POST MODS HERE (Verc)
My 94 Honda Civic Si / Type-R Specs:
Motor - 97 USDM ITR B18C5 #0075
Toda Spec B cams
Toda valve springs
Toda 2nd gen. cam gears
Portflow retainers
P28 chipped ECU
AEM adjustable FPR
Mugen 2 layer headgasket
Mugen Si-R 2 motor mounts
Fluidyne full length Integra radiator
Intake - 3" AEM CAI
Exhaust - Thermal stainless 2.25"
JDM Spoon 4-2-1 header
JDM ITR cat.
Trans. - ITR S80 w/ A.T.S. clutch type LSD,
A.T.S 4.93 final drive
Toda 9lb flywheel
B&M Pro Edge shifter and bushing kit
Suspension - RG (Racing Gear) JTC N1 circuit dampers
5 way adjustable damping, 12k / 10k springs
RG upper pillow ball mounts
26mm Mugen rear swaybar
Mugen front and rear strut bars
Mugen hard durometer bushings
Skunk 2 camber kit (front)
J's Racing camber (rear)
Brakes - ITR 5x114.3 (11.1 front 10.2 rear)
ITR Brake Pads (street)
Hawk Brake Pads (race)
Goodridge braided steel lines
Body -Denji Projector headlights
Clear Markers
Clear / Red Tail lights
Wings West RS Series Lip spoiler
Grill Craft
2000 ITR Wheels w/ 195.55.15 Bridgestone RE010
Kosei K-1 Racing wheels w/ 205.50.15 AVS
Kosei K-1 Racing wheels w/ 22 x 8 x 15 M/T drag slicks
Volk TE-37 Racing wheels w/ 225.45.15 Hoosier's
Interior
JDM ITR steering wheel
JDM ITR shift **** & boot
Recaro SRD seats
Sparco EVO (race)
ITR Rear seat
JDM Civic Type-R floormats
TRW Sabelt 5 Point Harness
OMP Pedals
Auto Power 4pt rollbar
Being Installed soon:
JDM EG rear spoiler
Freshly debadged hood
Autometer gauges & warning lights
sorry about the long post, but i copied and pasted it.....
#3
New User
Join Date: Sep 2001
Location: VanCity, BC, Canada
Posts: 151
Likes: 0
Received 0 Likes
on
0 Posts
Re: POST MODS HERE (rodney)
My 94 Honda Civic Si / Type-R Specs:
Motor - 97 USDM ITR B18C5 #0075
Toda Spec B cams
Toda valve springs
Toda 2nd gen. cam gears
Portflow retainers
P28 chipped ECU
AEM adjustable FPR
Mugen 2 layer headgasket
Mugen Si-R 2 motor mounts
Fluidyne full length Integra radiator
Intake - 3" AEM CAI
Exhaust - Thermal stainless 2.25"
JDM Spoon 4-2-1 header
JDM ITR cat.
Trans. - ITR S80 w/ A.T.S. clutch type LSD,
A.T.S 4.93 final drive
Toda 9lb flywheel
B&M Pro Edge shifter and bushing kit
Suspension - RG (Racing Gear) JTC N1 circuit dampers
5 way adjustable damping, 12k / 10k springs
RG upper pillow ball mounts
26mm Mugen rear swaybar
Mugen front and rear strut bars
Mugen hard durometer bushings
Skunk 2 camber kit (front)
J's Racing camber (rear)
Brakes - ITR 5x114.3 (11.1 front 10.2 rear)
ITR Brake Pads (street)
Hawk Brake Pads (race)
Goodridge braided steel lines
Body -Denji Projector headlights
Clear Markers
Clear / Red Tail lights
Wings West RS Series Lip spoiler
Grill Craft
2000 ITR Wheels w/ 195.55.15 Bridgestone RE010
Kosei K-1 Racing wheels w/ 205.50.15 AVS
Kosei K-1 Racing wheels w/ 22 x 8 x 15 M/T drag slicks
Volk TE-37 Racing wheels w/ 225.45.15 Hoosier's
Interior
JDM ITR steering wheel
JDM ITR shift **** & boot
Recaro SRD seats
Sparco EVO (race)
ITR Rear seat
JDM Civic Type-R floormats
TRW Sabelt 5 Point Harness
OMP Pedals
Auto Power 4pt rollbar
Being Installed soon:
JDM EG rear spoiler
Freshly debadged hood
Autometer gauges & warning lights
sorry about the long post, but i copied and pasted it.....
Nice list of mods man....
More pics of your car please!
#5
Honda-Tech Member
Join Date: May 2001
Location: Midwest
Posts: 5,698
Likes: 0
Received 0 Likes
on
0 Posts
Re: POST MODS HERE (DragIIcivic)
POST MODS HERE
no, it's none of your beezwax
no, it's none of your beezwax
Here is what I got, not a big list like that other guy, but I guess I have less money to spend then him!
b16a2 Swap.
Tanabe Racing Medallion Cat-Back.
Catco High Flow Cat.
Energy Suspension Polyurathane Engine Mount Inserts.
Rear Disc Brake Conversion.
99 Si Master Cylinder.
99 Si Prop Valve.
99 Si Rear Sway Bar
99 Si Guage Cluster.
99 Si Seats.
99 Si Tail Lights.
Hondata Stage 3 with OBD2 to OBD1 conversion.
Oh, and I can't forget the 20% Tint!!! Big HP gains there!
And what I want...hmmmm....
B18c1 short block
High Comp Pistons
Forged Rods
Toda or Jun Cams....and all the stuff that is needed for them to work good. I will just most likely begin working on a new engine this winter. I was going to do a B20VTEC, but I have decided against that because of my frequent high revving tendencies!!
[Modified by HXMan, 4:56 PM 10/5/2001]
#7
Honda-Tech Member
Join Date: May 2001
Location: Midwest
Posts: 5,698
Likes: 0
Received 0 Likes
on
0 Posts
Re: POST MODS HERE (DeceitfulCivic)
Rodney, your Type R civic has reminds me why I started this hobby, and also gives me areason to live. Truly a spectacular ride!
Trending Topics
#8
I forgot more about hondas then you will ever know....
Join Date: Feb 2001
Location: hop,skip, and a jump from the city,, new friggin york, USA
Posts: 5,310
Likes: 0
Received 1 Like
on
1 Post
Re: POST MODS HERE (DeceitfulCivic)
Rodney, your Type R civic has reminds me why I started this hobby, and also gives me areason to live. Truly a spectacular ride!
#9
Honda-Tech Member
Re: POST MODS HERE (rodney)
HAHA YEA
you tell her
one more part thats all i need!
just like my priorites.
1)Car
2)Hockey
3)Women
4)Work (just so i can get money for no. 1)
5)School
you tell her
one more part thats all i need!
just like my priorites.
1)Car
2)Hockey
3)Women
4)Work (just so i can get money for no. 1)
5)School
#10
Honda-Tech Member
Re: POST MODS HERE (rodney)
Rodney, your Type R civic has reminds me why I started this hobby, and also gives me areason to live. Truly a spectacular ride!
wow! thanks for the compliment. i need to update the pics/mods. much has changed. i forgot to mention i ordered up a ARC dual filter intake for a ek, i'm going to mod that to fit my eg. the wifey wants to buy a house, but i told her i need just one more part......
wow! thanks for the compliment. i need to update the pics/mods. much has changed. i forgot to mention i ordered up a ARC dual filter intake for a ek, i'm going to mod that to fit my eg. the wifey wants to buy a house, but i told her i need just one more part......
I bet it is a stormer of a clamshell racer though, mucho mucho props. so clean, so PRO!
ARGGGGHHHHH! my hatch will be a junior edition of your setup... man you got the FINE stuff.
A+ for you rodney.
#11
Honda-Tech Member
Join Date: Aug 2001
Location: So.Cal, USA
Posts: 340
Likes: 0
Received 0 Likes
on
0 Posts
Re: POST MODS HERE (owen_the_soyboy)
95 Civic Coupe
---B16A
---JE Pistons
---Total Seal Rings
---Crower Connecting Rods
---NuFormz Block Guard
---Micropolished & Knife-Edged Crank
---Decked, O-Ringed, Honed, etc...
---Integra Type-R Camshafts
---Garrett T3/T04E Turbocharger
---Rev Hard Manifold
---Turbonetics Wastegate
---Rev Hard Large Polished Intercooler
---Custom Piping (Dynamic Design)
---GReddy Type-S Blow Off Valve
---AEM Tru Power Pulleys
---AEM Tru Time Cam Gears
---Integra Type-R Intake Manifold
---RC 62mm Overbored Throttle Body
---MSD 6AL Ignition
---MSD Blaster 3 Coil
---MSD Pro Cap
---Aramaki wires
---GReddy Power Extreme Exhaust
---RC 270cc Injectors
---Vortech MaxFlow Power Fuel Rail
---Holley 255lph In Tank Fuel Pump
---B&M Command Flo
---B&M Fuel Pressure Gauge
---GReddy Oil Catch Can
---Mugen P-28 ECU
---A'pexi V-AFC
---Exedy Clutch
---GReddy 52mm white boost gauge
---GReddy turbo timer
---HKS EVC IV
---AutoMeter 52mm white Air:Fuel Meter
---AutoMeter 52mm white Oil Pressure Meter
---Auto Power 4-pt. rollbar
---AutoMeter shift light w/ 8K pills
---Front & Rear strut tower braces
---Wings West front chin spoiler
---H&R Sport Springs
---Power Stop slotted & cross drilled rotors
---Axxis Metal Masters pads
---Good Set of Pep Boys Hood Pins
Future:
---Apexi Power FC w/Commander
---720CC Injectors
---Complete Crower Valvetrain
---New Valve Guides
---Dyno Tuning very soon
[Modified by TheBoostieBoys, 7:37 PM 10/6/2001]
---B16A
---JE Pistons
---Total Seal Rings
---Crower Connecting Rods
---NuFormz Block Guard
---Micropolished & Knife-Edged Crank
---Decked, O-Ringed, Honed, etc...
---Integra Type-R Camshafts
---Garrett T3/T04E Turbocharger
---Rev Hard Manifold
---Turbonetics Wastegate
---Rev Hard Large Polished Intercooler
---Custom Piping (Dynamic Design)
---GReddy Type-S Blow Off Valve
---AEM Tru Power Pulleys
---AEM Tru Time Cam Gears
---Integra Type-R Intake Manifold
---RC 62mm Overbored Throttle Body
---MSD 6AL Ignition
---MSD Blaster 3 Coil
---MSD Pro Cap
---Aramaki wires
---GReddy Power Extreme Exhaust
---RC 270cc Injectors
---Vortech MaxFlow Power Fuel Rail
---Holley 255lph In Tank Fuel Pump
---B&M Command Flo
---B&M Fuel Pressure Gauge
---GReddy Oil Catch Can
---Mugen P-28 ECU
---A'pexi V-AFC
---Exedy Clutch
---GReddy 52mm white boost gauge
---GReddy turbo timer
---HKS EVC IV
---AutoMeter 52mm white Air:Fuel Meter
---AutoMeter 52mm white Oil Pressure Meter
---Auto Power 4-pt. rollbar
---AutoMeter shift light w/ 8K pills
---Front & Rear strut tower braces
---Wings West front chin spoiler
---H&R Sport Springs
---Power Stop slotted & cross drilled rotors
---Axxis Metal Masters pads
---Good Set of Pep Boys Hood Pins
Future:
---Apexi Power FC w/Commander
---720CC Injectors
---Complete Crower Valvetrain
---New Valve Guides
---Dyno Tuning very soon
[Modified by TheBoostieBoys, 7:37 PM 10/6/2001]
#15
Member
Join Date: Oct 2001
Location: Philadelphia, PA
Posts: 7,830
Likes: 0
Received 0 Likes
on
0 Posts
Re: POST MODS HERE (Verc)
Holy Smokes Rodney....
Are yoo some type of CRACK DEALER ?!?!?!?!
Yoo better hook me up with some of yoor products...
I want yoor kind of INCOME ! ! !
Are yoo some type of CRACK DEALER ?!?!?!?!
Yoo better hook me up with some of yoor products...
I want yoor kind of INCOME ! ! !
#20
Banned
Join Date: Dec 2000
Location: arlington, tx, us
Posts: 299
Likes: 0
Received 0 Likes
on
0 Posts
Re: POST MODS HERE (KAMiN)
98 civic
ls/vtec
gs-r tranny
headers
cam sprockets
intake
exhaust
str block guard
nos plate system
girdle
act street disc
b&m fpr
nology wires
crane cams ignition
ls/vtec
gs-r tranny
headers
cam sprockets
intake
exhaust
str block guard
nos plate system
girdle
act street disc
b&m fpr
nology wires
crane cams ignition
#21
New User
Join Date: Mar 2001
Location: Tulsa, OK, USA
Posts: 60
Likes: 0
Received 0 Likes
on
0 Posts
Re: POST MODS HERE (98 Ek LsVtec)
99 Si
-AEM Underdrive Pulley (PS)
-AEM CAI
-Neuspeed Sway Bar
-DC Front Strut Tower Bar
-DC Rear Upper Strut Tower Bar
-DC Lower Tie Bar
-DC 4-1 SS Header
-ClutchMasters Stage 3 Clutch
-Thermal R&D "Stealth" Exhaust
-Mugen Thermosat
-Mugen Radiator Cap
-TEIN Type NR Dampers with soft springs
-JRSC (6psi)
-Jackson Racing Gauges (A/F, Boost)
-Jackson Racing Liquid Intercooler
-APEXi VAFC
-CTR Valve Cover
I think that's it, can't remember right now...
-AEM Underdrive Pulley (PS)
-AEM CAI
-Neuspeed Sway Bar
-DC Front Strut Tower Bar
-DC Rear Upper Strut Tower Bar
-DC Lower Tie Bar
-DC 4-1 SS Header
-ClutchMasters Stage 3 Clutch
-Thermal R&D "Stealth" Exhaust
-Mugen Thermosat
-Mugen Radiator Cap
-TEIN Type NR Dampers with soft springs
-JRSC (6psi)
-Jackson Racing Gauges (A/F, Boost)
-Jackson Racing Liquid Intercooler
-APEXi VAFC
-CTR Valve Cover
I think that's it, can't remember right now...
#22
Honda-Tech Member
Join Date: Dec 2000
Location: JDM Land, Canada
Posts: 2,129
Likes: 0
Received 0 Likes
on
0 Posts
Re: POST MODS HERE (Verc)
Here's my engine mod:
97 Honda Civic (Engine mods only)
-B18C5 Engine
-AJR Forged pistons CR 12.5:1
-AJR balanced / bluerpinted
-AJR P/P cylinder head
-AJR custom carbon air box
-AJR custom oil cooler kit (Earl's)
-AJR custom ECU
-AJR machined TB
-Spoon B18C rods
-Spoon titanium retainers
-Spoon 421 header
-Spoon Plug wires w/ground
-Spoon cams
-Spoon camgears
-Spoon polished rockers
-Spoon valvesprings
-Spoon valve seals
-Spoon head gasket
-Spoon racing plugs
-Spoon test pipe
-Spoon shiftlinkage / bushings
-Spoon engine mounts
-Spoon radiator hose
-Spoon aluminum 3 core radiator
-Spoon L.S.D.
-Spoon Injectors
-Spoon carbon plug cover
-Spoon Timing belt
-SRR oil catch can
-JDM CTR Crank pulley
-ATS carbon clutch w flywheel (holds up to 1280kg/f)
-ATS Close gear ratio set (1-2-3-4-5)
-Type One Ti exhaust
[Modified by AJ PwR, 11:02 PM 10/7/2001]
97 Honda Civic (Engine mods only)
-B18C5 Engine
-AJR Forged pistons CR 12.5:1
-AJR balanced / bluerpinted
-AJR P/P cylinder head
-AJR custom carbon air box
-AJR custom oil cooler kit (Earl's)
-AJR custom ECU
-AJR machined TB
-Spoon B18C rods
-Spoon titanium retainers
-Spoon 421 header
-Spoon Plug wires w/ground
-Spoon cams
-Spoon camgears
-Spoon polished rockers
-Spoon valvesprings
-Spoon valve seals
-Spoon head gasket
-Spoon racing plugs
-Spoon test pipe
-Spoon shiftlinkage / bushings
-Spoon engine mounts
-Spoon radiator hose
-Spoon aluminum 3 core radiator
-Spoon L.S.D.
-Spoon Injectors
-Spoon carbon plug cover
-Spoon Timing belt
-SRR oil catch can
-JDM CTR Crank pulley
-ATS carbon clutch w flywheel (holds up to 1280kg/f)
-ATS Close gear ratio set (1-2-3-4-5)
-Type One Ti exhaust
[Modified by AJ PwR, 11:02 PM 10/7/2001]
Thread
Thread Starter
Forum
Replies
Last Post