My K24A2 swapped JRSC DC5
10-13-2011, 07:58 PM
#51
DC5/EP3 MOD :)
Thread Starter
Re: My K24A2 swapped JRSC DC5
Got rid of the v-lip and got a top one splitter
Silver is the old... black is the newer bigger better~!
Ok so before:
and then I took out my center grill
and put two giant washers evenly to mark drill holes
Then connected the new rods.
Then marked holes for the bolts going thru the splitter and connected them and walla!
Silver is the old... black is the newer bigger better~!
Ok so before:
and then I took out my center grill
and put two giant washers evenly to mark drill holes
Then connected the new rods.
Then marked holes for the bolts going thru the splitter and connected them and walla!
10-16-2011, 04:59 PM
#53
DC5/EP3 MOD :)
Thread Starter
Re: My K24A2 swapped JRSC DC5
Got some new parts and had a photoshoot today... photos wont be ready for a week or so but I snapped a quick cell phone picture or two
up close shot of the new winglets, splitter and rods
up close shot of the new winglets, splitter and rods
10-16-2011, 05:00 PM
#54
DC5/EP3 MOD :)
Thread Starter
10-18-2011, 01:05 PM
#58
DC5/EP3 MOD :)
Thread Starter
10-20-2011, 09:08 PM
#61
DC5/EP3 MOD :)
Thread Starter
Re: My K24A2 swapped JRSC DC5
Well another season has come and gone for my DC5. She will be in storage end of next week. So this week between rain storms, heavy winds, and the freezing cold weather I snapped off some video footage and put together an end of the year video.
I'm no pro but I enjoy editing. So I tried to keep it clean and did what I could with what I had! It's all shot with a small GoPro. Someday I'll stop buying car parts so I can buy a video camera!
Anyways, Here it is: Fall is Here...
http://www.youtube.com/watch?v=mv1Qp5tPc-4
I'm no pro but I enjoy editing. So I tried to keep it clean and did what I could with what I had! It's all shot with a small GoPro. Someday I'll stop buying car parts so I can buy a video camera!
Anyways, Here it is: Fall is Here...
http://www.youtube.com/watch?v=mv1Qp5tPc-4
10-24-2011, 01:55 PM
#64
DC5/EP3 MOD :)
Thread Starter
10-28-2011, 07:34 PM
#66
DC5/EP3 MOD :)
Thread Starter
Re: My K24A2 swapped JRSC DC5
So I decided to do a little upgrade today... then again what's new 
So I decided the fakatas had to go! Here is what I had
and here is the back where I had it crossed incorrectly cause at the time I didn't know what I was doing lol
But now I have FIA/SFI approved harnesses from G-Force
The quality on these things are absolutely amazing. So much better, thicker, stronger and nicer than my knockoffs.
Installed
and the rear wrapped properly
So I decided the fakatas had to go! Here is what I had
and here is the back where I had it crossed incorrectly cause at the time I didn't know what I was doing lol
But now I have FIA/SFI approved harnesses from G-Force
The quality on these things are absolutely amazing. So much better, thicker, stronger and nicer than my knockoffs.
Installed
and the rear wrapped properly
11-01-2011, 05:27 PM
#67
DC5/EP3 MOD :)
Thread Starter
Re: My K24A2 swapped JRSC DC5
So my second harness came in today! woot, another item off the parts list.
couldn't be happier with the end product and look
couldn't be happier with the end product and look
12-21-2011, 06:54 PM
#72
DC5/EP3 MOD :)
Thread Starter
Re: My K24A2 swapped JRSC DC5
Well I will start updating my new build... special thanks to PhilipR for all his help so far!
I will just post pictures in order!
Start by removing bumpers
Then removed some more parts lol like the engine! haha
from there I started working on removing everything... started with:
then
kept stripping.. now fenders and more lines etc.
started a good collection of parts lying around lol
Now for the fun!!! Time to start welding!
this is as far as I've gotten... I'm just started to grind down all of the welds.
I will just post pictures in order!
Start by removing bumpers
Then removed some more parts lol like the engine! haha
from there I started working on removing everything... started with:
then
kept stripping.. now fenders and more lines etc.
started a good collection of parts lying around lol
Now for the fun!!! Time to start welding!
this is as far as I've gotten... I'm just started to grind down all of the welds.
