Greddy Boost Controller Profec B spec 2
09-14-2007, 08:03 PM
#1
Honda-Tech Member
Thread Starter
Join Date: Oct 2002
Location: Pittsburgh, PA, USA
Posts: 1,179
Likes: 0
Received 0 Likes
on
0 Posts
Greddy Boost Controller Profec B spec 2
Just hooked this bitch uo and I am not sure if I am missing something. I have it in psi not 100kpa, at idel its at -99 and at about 3 or 4 psi its reading 29 and the alarm is going off. Could that be 2.9psi? But at idel its at -99 that cant be 9.9 because my manual boost guage is reading about 20.
please any help
please any help
09-14-2007, 08:38 PM
#2
Member
Join Date: Apr 2003
Location: KILLLLLLA, CALI, usa
Posts: 1,851
Likes: 0
Received 0 Likes
on
0 Posts
Re: Greddy Boost Controller Profec B spec 2 (nitroice40)
what did you set your warning at? i just put mines in too.. try setting your warning 1 psi higher then your set psi..
09-15-2007, 07:31 AM
#3
Honda-Tech Member
Thread Starter
Join Date: Oct 2002
Location: Pittsburgh, PA, USA
Posts: 1,179
Likes: 0
Received 0 Likes
on
0 Posts
Re: Greddy Boost Controller Profec B spec 2 (turboekcivic)
I set low at 18 and warning at 20. At about 3psi the warning was going off.
09-15-2007, 07:55 AM
#4
Honda-Tech Member
iTrader: (1)
Join Date: Feb 2003
Location: somewhere in..., pa, usa
Posts: 3,923
Likes: 0
Received 0 Likes
on
0 Posts
Re: Greddy Boost Controller Profec B spec 2 (nitroice40)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by nitroice40 »</TD></TR><TR><TD CLASS="quote"> But at idel its at -99 that cant be 9.9 because my manual boost guage is reading about 20.
</TD></TR></TABLE>
More than likely, your boost gauge is reading vacuum as in/hg at 20 and the ebc is reading in psi at 9.9. 9.9 in psi is the same as about 20 in/hg....just throwing my $0.02 out there
</TD></TR></TABLE>
More than likely, your boost gauge is reading vacuum as in/hg at 20 and the ebc is reading in psi at 9.9. 9.9 in psi is the same as about 20 in/hg....just throwing my $0.02 out there
09-15-2007, 06:15 PM
#5
Honda-Tech Member
Join Date: Sep 2005
Posts: 831
Likes: 0
Received 0 Likes
on
0 Posts
Re: Greddy Boost Controller Profec B spec 2 (nitroice40)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by nitroice40 »</TD></TR><TR><TD CLASS="quote">Could that be 2.9psi? But at idel its at -99 that cant be 9.9 because my manual boost guage is reading about 20.
please any help</TD></TR></TABLE>
the EBC reads PSI in x10 format. so a reading of 70 would be 7 PSI
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by PA MATT »</TD></TR><TR><TD CLASS="quote">
More than likely, your boost gauge is reading vacuum as in/hg at 20 and the ebc is reading in psi at 9.9. 9.9 in psi is the same as about 20 in/hg....just throwing my $0.02 out there</TD></TR></TABLE>
yes and 9.9 PSI would read as 99 on the EBC or (-99 in the case of vacuum)
please any help</TD></TR></TABLE>
the EBC reads PSI in x10 format. so a reading of 70 would be 7 PSI
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by PA MATT »</TD></TR><TR><TD CLASS="quote">
More than likely, your boost gauge is reading vacuum as in/hg at 20 and the ebc is reading in psi at 9.9. 9.9 in psi is the same as about 20 in/hg....just throwing my $0.02 out there</TD></TR></TABLE>
yes and 9.9 PSI would read as 99 on the EBC or (-99 in the case of vacuum)
09-15-2007, 07:15 PM
#6
Member
Join Date: Apr 2003
Location: KILLLLLLA, CALI, usa
Posts: 1,851
Likes: 0
Received 0 Likes
on
0 Posts
Re: Greddy Boost Controller Profec B spec 2 (oranginal)
are you sure its hitting warning at 3psi? something is wrong unless your spiking really bad... check your peak
Thread
Thread Starter
Forum
Replies
Last Post
B16Civic93
Forced Induction
7
05-12-2005 01:12 PM
