Full Race SR20DET Equal length manifold vs Company X...
06-05-2003, 07:31 AM
#1
Honda-Tech Member
Thread Starter
Join Date: May 2001
Location: FULL RACE, AZ, USA
Posts: 4,719
Likes: 0
Received 0 Likes
on
0 Posts
Full Race SR20DET Equal length manifold vs Company X...
http://forums.freshalloy.com/u...art=1
....
Well,
We finally got the car back on the rollers last night after hours. tuning was with 93 octane only no race gas. After talking to alot of other tuners we decided to not take it above 400 Hp on 93. That proved to be a tough task...LOL
405Hp / 308Tq @ 1.05 Bar (15.2 psi) - SAE Correction
Dyno Graph to be posted later today...
That is the same power at 1 psi less than my previous setup, however, these runs were done with Full 3" exhaust ( before it was open 3" downpipe). AND...last night it was about 95 Deg F up on the dyno (gotta love florida) where as the previous runs were done at 65 Deg F ambient. Furthermore i think more gains could be had from cam gear tuning. we picked up SO much last time dialing in the cams...but that was to the old flow characteristics of the motor, this manifold has drastically changed the flow properties of the engine
So to sum up... The Full-race manifold works very well. It made the same power at less boost even with far less favorable conditions, and a full exhaust.
want to know what it's like to go for a ride?? go check this thread.. Mr. X took the car for a test ride after tuning last night.
http://forums.freshalloy.com/u...art=1
Scott
....
Well,
We finally got the car back on the rollers last night after hours. tuning was with 93 octane only no race gas. After talking to alot of other tuners we decided to not take it above 400 Hp on 93. That proved to be a tough task...LOL
405Hp / 308Tq @ 1.05 Bar (15.2 psi) - SAE Correction
Dyno Graph to be posted later today...
That is the same power at 1 psi less than my previous setup, however, these runs were done with Full 3" exhaust ( before it was open 3" downpipe). AND...last night it was about 95 Deg F up on the dyno (gotta love florida) where as the previous runs were done at 65 Deg F ambient. Furthermore i think more gains could be had from cam gear tuning. we picked up SO much last time dialing in the cams...but that was to the old flow characteristics of the motor, this manifold has drastically changed the flow properties of the engine
So to sum up... The Full-race manifold works very well. It made the same power at less boost even with far less favorable conditions, and a full exhaust.
want to know what it's like to go for a ride?? go check this thread.. Mr. X took the car for a test ride after tuning last night.
http://forums.freshalloy.com/u...art=1
Scott
06-05-2003, 07:56 AM
#2
New User
Join Date: Nov 2000
Location: Tampa, FL, USA
Posts: 3,467
Likes: 0
Received 0 Likes
on
0 Posts
Re: Full Race SR20DET Equal length manifold vs Company X... (FFgeoff)
stealing my thunder eh?
In case anyone remembers, the car in question here is the same one I posted about a couple of months ago. We're expecting big big numbers on race gas.
In case anyone remembers, the car in question here is the same one I posted about a couple of months ago. We're expecting big big numbers on race gas.
06-05-2003, 07:57 AM
#3
Honda-Tech Member
Thread Starter
Join Date: May 2001
Location: FULL RACE, AZ, USA
Posts: 4,719
Likes: 0
Received 0 Likes
on
0 Posts
Re: Full Race SR20DET Equal length manifold vs Company X... (VaporTrail)
heheh i didnt know you were online 
i got excited, since this is better than an equal length vs log comparo, equal length vs equal length is more interesting.
i got excited, since this is better than an equal length vs log comparo, equal length vs equal length is more interesting.
06-05-2003, 08:11 AM
#5
Honda-Tech Member
Thread Starter
Join Date: May 2001
Location: FULL RACE, AZ, USA
Posts: 4,719
Likes: 0
Received 0 Likes
on
0 Posts
Re: Full Race SR20DET Equal length manifold vs Company X... (bambooluv)
We made one KA manifold, but there has been little to no interest as most KA guys are very budget minded, and love log manis.
06-05-2003, 08:18 AM
#6
Honda-Tech Member
Join Date: Aug 2001
Location: Duluth, GA
Posts: 365
Likes: 0
Received 0 Likes
on
0 Posts
Re: Full Race SR20DET Equal length manifold vs Company X... (FFgeoff)
Will this mani only fit the rwd det or will it also fit the fwd det in the se-r?
Nice numbers by the way.
Nice numbers by the way.
06-05-2003, 08:38 AM
#7
New User
Join Date: Nov 2000
Location: Tampa, FL, USA
Posts: 3,467
Likes: 0
Received 0 Likes
on
0 Posts
Re: Full Race SR20DET Equal length manifold vs Company X... (teamrocket si)
i dont think the turbo would clear the hood in FWD configuration, most SR manifolds are bottom mount for FWD, this one is top mount.
Trending Topics
06-05-2003, 08:47 AM
#8
Honda-Tech Member
Thread Starter
Join Date: May 2001
Location: FULL RACE, AZ, USA
Posts: 4,719
Likes: 0
Received 0 Likes
on
0 Posts
Re: Full Race SR20DET Equal length manifold vs Company X... (teamrocket si)
rwd, the fwd is being prototyped right now, but its completely different.
pic of the rwd
front view
top view
bottom view
some welds
pic of the rwd
front view
top view
bottom view
some welds
Finally I get to see my wastegate JON.
06-05-2003, 11:09 AM
#14
Honda-Tech Member
Join Date: Jan 2003
Location: A Place in, Florida, USA
Posts: 7,277
Likes: 0
Received 0 Likes
on
0 Posts
Re: Full Race SR20DET Equal length manifold vs Company X... (FFgeoff)
I have not seen Scott's car with the new manifold yet but even before the Full Race manifold is was one bad ***** ...
OLD DYNO SHEET
http://photos.yahoo.com/bc/alp...iew=t
http://photos.yahoo.com/bc/alp...iew=t
http://photos.yahoo.com/bc/alp...iew=t
OLD DYNO SHEET
http://photos.yahoo.com/bc/alp...iew=t
http://photos.yahoo.com/bc/alp...iew=t
http://photos.yahoo.com/bc/alp...iew=t
06-05-2003, 03:25 PM
#20
Honda-Tech Member
Join Date: Aug 2001
Location: www.js-garage.com
Posts: 6,470
Likes: 0
Received 0 Likes
on
0 Posts
Re: (javierb14)
Is that a jdm cluster?? seems like 1st gear goes to around 50 something.....
Thats a very nice car... what is it expected to run in the quarter?
Thats a very nice car... what is it expected to run in the quarter?
06-05-2003, 04:00 PM
#25
Honda-Tech Member
Join Date: Jan 2003
Location: A Place in, Florida, USA
Posts: 7,277
Likes: 0
Received 0 Likes
on
0 Posts
Re: (prelude beast)
The one in the video is a Garrett GT3040.
http://photos.yahoo.com/bc/alp...iew=t
http://photos.yahoo.com/bc/alp...iew=t
http://photos.yahoo.com/bc/alp...iew=t
http://photos.yahoo.com/bc/alp...iew=t