850hp percision intercooler w/ 50mm tial BOV 3" intercooler pipe hot side

3.5" intercooler pipe cold side. fits all eg civic and integra.


pictures
http://img703.imageshack.us/g/dscn0804k.jpg/

 

I'm selling a brand new BPi Flowstack with K&N Filter. This set up also comes with a brand new 3"SRI intake pipe. This includes all C clamps, hoses and couplers necessary to install on vehicle. For those that do not know this set-up performs very well on NA Honda's; I've attached a dyno comparison between the AEM 3" CAI vs the BPi flowstack on a b18c1. This mod is one of the best bangs for your buck as far as hp per dollar is concerned.

BPi's test portion of their website
http://www.bpinitiatives.com/testing.php

Dyno chart taken from BPi's website: Comparison of the BPi Flow Stack with K&N Filter RP-4600 and 3" AEM Filter on a Honda B18c1 motor. No additional tuning was performed after the installation of the Flow Stack.


$115 shipped via FedEx with tracking # to your door. I've recently sold a ton of stuff on H-T lately so rest assured you're dealing with a reputable seller.

 

RCREW K20 Race Header.
This header has been used on the dyno only. selling for $500 obo

 

New exedy twin plate clutch for a b-tranny,1100 shipped.
Blue tial 44 w.g. like new,250 shipped.
Skunk2 pro series cam gears (titanium) like new,160 shipped. SOLD!!!
AEM blue 5 bolt cam gears like new,90 shipped. SOLD!!!
Fluidampr Race version for B-engines like new,280 shipped.
G-Force/Long shifter with Long handle and shifter **** NEW.No bracket or shift linkage included.585 shipped.

 

I have for sale freshly sleeved K20a2 block done by RS machines it is at 89mm bore,New custom Arias pistons and eagle rods and a k20a2 crank for sale.This is a bare block.Selling everything for $1500.

 

All parts for Acura Rsx Type S

StopTech BBK RSX S
1k miles. pads 95% $1000 Shipped.
Complete kit. Everything included even SB lines


Buddy Club Low down seat rails


Pass+Driver seat rails $200 shipped



Driveshaft Shop Level 2.9 Axles 1k miles $600 Shipped

 

BRAND NEW skunk2 70mm throttle body for B/D/H series
$250 shipped/paypal'd



AEM FPR for B series, great condition, with -6an return fitting
$85 shipped/paypal'd




-BRAND NEW skunk2 cam seal
-$25 shipped/paypal'd




-used NOS nitrous setup, with plate setup for a GSR.. plate bolts in place of the factory butterflys on stock mani.. really nice setup
-more info on the setup: http://www.hawkinsspeedshop.com/cate...duct-1280.html
-$300 shipped/paypal’d?

 

WALBRO INLINE FUEL PUMP-USED $40


OBD-O TO OBD-1 DISTRIBUTOR CONVERSION HARNESS $40



K20 INLINE PRO TURBO MANIFOLD WITH 38MM OR 44MM WASTEGATE OPTION $220



B18 GSR and B18 LS and EVO Intake Mani Hondata Gasket $50 each *NEW


K20/K24 and S2000 Coil Packs $40 each


B18C ITR (Type-R) OBD-IIA ECU $80


Place Racing Mounts H22 in DA 90-93 Integra Kit **NEW (just has some dust and over spray on them) $180


B-Series Turbo Parts/Kit (includes) Full-Race Ramhorn Manifold, Tial 40mm wastegate, Precision SC61 Turbo, 3" Down Pipe (Made 550 WHP on 20psi) Mint Condition. $1199




Tein 95-99 Mitsubishi Eclipse Tein SS Suspension (adjustable) **NEW -Complete $400


Tein 95-99 Mitsubishi Tein Pillow Top Mounts $120 (all 4)


AUTO TO MANUAL CONVERSION TRANNY MOUNT EG/DC CHASSIS - NEW $60



***Prices do not include shipping ans are OBO***

 

sold

 

DSS stg 2.9 axels. Used for about 3k $550+ shipping
Full-Race SFWD T4 Twinscroll topmount with logo. you can tell this mani has very little time on it.. probably a few hrs of run time....barely used. supersuper clean/ mint.mint.mint $1000 OBO + shipping
I would postpox but im listing from my cell therefore i cannot. Txt for pix.parts again are mint and are in 100% perfect working order... Dan@57Zero-49Zero-89Zero8

 

I have an almost new fluidamper race damper for any b series motor for sale asking $250 shipped.

 

Bosch 1600's FS, can go with an fjo driver a well. Looking to sell or trade for some id1000s. Name your price

 

barely used comp stage 5 clutch kit & flywheel.... has a little over 600 miles on it only took it out because I needed a twin disc... Asking $340 together new they go for around 520... NO TRADES








PWR intercooler rated for 500hp 27 1/2 x 7 1/4 x 2 3/4..made 620hp with no problems
Asking $250

 

Franks Custom Fiberglass 3 piece front end. Brand spanking new only bolted up for the pics. we just aren't feeling it like we thought we would. Normally these are cut out for 26'2 but if you look in the angle with the slick you can see a black trim that he left for the 24.5 for me but if i decided to go 26 thats all you need to cut out.
$700 you cover the shipping.

 

FS: Wilwood Drag front brakes... drops 11lbs per side..... Will Not allow anything smaller than a 15 inch wheel! $600 SHIPPED WITH STEEEL BRAIDED LINES!

 

MW pro 10, with pigtail and ps92 coil used. 500.00

 

I will update this post with pics as I remove parts from the car.


Complete Long block without manifolds $2850 Includes the following :
700+ whp tested and proven motor

Ka24de
Wiseco Pistons 89.5MM bore w/upgraded wrist pins 9:1 compression
Pauter Rods
Cometic Headgasket
11mm L19 headstuds
ARP main Studs
ATI Crank damper
Shimmed oil pump regulator
Cometic MLS headgasket
BC Stage 3 Cams
BC Springs and Retainers
Balanced rotating assembly
Starter
Alternator
CAS w/ 24 tooth aem trigger wheel
Custom Solid motor mounts




Custom Intake Manifold for 8 injector setup $1350 Includes:

Two fuel rails powder coated black w/ -6AN in and out fittings
Billet 80mm Throttle body w/nissan TPS already mounted.






Turbo Kit $3000 Includes:

Custom Long Runner stainless Steel T4 Divided Manifold
2 x Tial 44mm wastegates
2 x Stainless Steel Dumptubes
Borg Warner S372R Turbo with Race Cover and 1.25AR rear housing
Tial Q BOV welded onto compressor cover
4" Stainless Steel Downpipe
Custom Turbo Hanger with Heim Joint
Hotshot Performance Coatings Inc, Coated Manifold/turbine housing/dumptubes





KA to VG transmission Adapter $1100 Includes:

300zx transmission with bellhousing already machined down
Complete Mazworx trans adapter kit w/ aluminum driveshaft/shifter bracket/short shifter/tranny mount


Competition Clutch Twin Disk clutch w/ Alum Flywheel $750



M&W Pro 14 Ignition Setup With 4 CBR coils and Pre-made Harness $850

 

OBX B18B LS Limited Slip Diff

It was installed in a transmission, but I never put the car together so the diff is in NEW condition.

$300

K20A2 RSX Type S Head







Head comes as pictured with camshafts. Head is in good condition.
$800 OBO
PRICE LOWERED $700 OBO

 

CP 86mm 9.0:1 pistons with carrillo a-beam rods asking $1000.00



supertech dual valve springs and retainers asking $325.00

 

RCI 5 point harness Latch style BLACK Pretty much new $60 shipped still good

Also have the SnapON/bluepoint valvespring tool. $100 shipped

 

I have one Black 38mm Vband Wastegate left over from a turbo snowmobile setup we did.

Brand New in the Box.

.3 Bar Spring

$240 obo and I'll ship it to you for free.

Joe@DPIstore.net

 

NRG TECH V TECH KILLER CAMS FROM FERREA INTAKE SIDE Is a custom grind i have the spec ON THE exaust u will need to buy roller rockers and springs

B10019-E EXH Roller Cam. Road Racing/Turbo Applications 278-12.76 EXH 278 254 106 BTDC 12.76mm

pAID $1950 FOR THE CAMS NEVER USED THEM STILL BRAND NEW
$1900 OBO

have 2 NOS direct port kits with 2 full 10lb pound bottles i have 160 shot120 shot and 100 shot set of jets both kits have a purge kit each have alot of extra hard lines all nos hardware
$450 per kit text me i can send pics

crower turbo 2 cams fits b16 and gsr heads $375
only have 10 hrs on them like new

(856) 332-5450

 

set of bogarts 15x10 and 15x3.5 26 tires all the way around ..800 to sell quick need a set of 13x9s or 10s also willing to trade ...u can rach me @904-226-8240

 

Precision Billet 6768 Ball Bearing with .96 Housing and AntiSurge H-Cover 4in\3out about 15 passes on it Perfect condition 2000 Shipped

 

Z10 Traction Bar EK\EG\DC- $200

BNIB revhard turbokit with sc6152-$2000

Full-race T3 ramhorn turbokit minus turbo and downpipe-$1500

Custom Synapse front mount turbokit T4 Divided with twin mvs wastegates, 35r 1.06 divided.-$3000

JG Edlebrock intake manifold B16 -$200

AEBS intake manifold B16-$100

Omnipower front lower control arms-$200

Carillo A beam gsr rods-$300

Crower gsr rods-$200

Manley turbotuff ls rods -$350

CTR pulley -$50

MSD two step module with adj. **** -$50

Apexi vafc- $50

Drag intercooler 22x6.5x2.25-$100

H22a4 aebs sleeved eagle rods, Je pistons Fully balanced
and assmbled. Brand new, never ran-$2000