Turbo EG driveline partout
#1
Honda-Tech Member
Thread Starter
Join Date: Feb 2005
Location: Arden, NC, USA
Posts: 758
Likes: 0
Received 0 Likes
on
0 Posts
Turbo EG driveline partout
Pricing does not include shipping, PM me for quote or offers.
Nearly all items are of top quality in like new condition.
See my other thread for non turbo parts.
http://www.hondamarketplace.com/show...6#post41128926
There is no carelessly built junk in this driveline, I've got a LOT of blood,sweat, and tears in this. If you don't recognize a part, I probably machined it, welded, or fabricated it myself. It would be ideal for buyers to buy the whole systems together since most of the parts are matched to each other.
Intercooler piping, 2.75" Fits perfect on an EG with the precision intercooler. Welded mandrel bends, silicone couplers and stainless T bolt clamps, IAT flange welded to pipe. Comes with extra bends, clamps and couplers, $150
SOLDSOLD Tial BOV SOLDSOLD
J&S ultra safeguard and knock monitor. This thing is good insurance on any turbo car IMO. Can easily see if you grab some bad gas or have any detonation going on. The device will automatically pull timing per cylinder until knock ceases. Read more - http://www.jandssafeguard.com/safeguard.html $260
Turbo heat shield, $20
Mfactory magnetic drain plugs $8
Turbo oil lines, flange, oil manifolds - make offers
Nearly all items are of top quality in like new condition.
See my other thread for non turbo parts.
http://www.hondamarketplace.com/show...6#post41128926
There is no carelessly built junk in this driveline, I've got a LOT of blood,sweat, and tears in this. If you don't recognize a part, I probably machined it, welded, or fabricated it myself. It would be ideal for buyers to buy the whole systems together since most of the parts are matched to each other.
Intercooler piping, 2.75" Fits perfect on an EG with the precision intercooler. Welded mandrel bends, silicone couplers and stainless T bolt clamps, IAT flange welded to pipe. Comes with extra bends, clamps and couplers, $150
SOLDSOLD Tial BOV SOLDSOLD
J&S ultra safeguard and knock monitor. This thing is good insurance on any turbo car IMO. Can easily see if you grab some bad gas or have any detonation going on. The device will automatically pull timing per cylinder until knock ceases. Read more - http://www.jandssafeguard.com/safeguard.html $260
Turbo heat shield, $20
Mfactory magnetic drain plugs $8
Turbo oil lines, flange, oil manifolds - make offers
Last edited by greasemonkee; 02-13-2010 at 01:10 PM.
Trending Topics
#14
Honda-Tech Member
Thread Starter
Join Date: Feb 2005
Location: Arden, NC, USA
Posts: 758
Likes: 0
Received 0 Likes
on
0 Posts
Re: Turbo EG driveline partout
On the GSR block - or all B series? - I think it was the power steering bracket bolt holes, not completely sure, that the platform bolted to for the shield. The intent was to keep some heat off the cold section and keep the air filter from getting debris built up on top of it.
#19
Honda-Tech Member
Join Date: Sep 2007
Location: murrieta, ca, usa
Posts: 3,546
Likes: 0
Received 0 Likes
on
0 Posts
Re: Turbo EG driveline partout
how much are you looking to get for some of the oil lines? the long oil feed( one wraped in red, but dont need the red thing) and one of the long return lines(what are the size of the 2? i need one closet to .6 inch inside diameter) and the silver return fitting near the center of the pix? cuz dont want to low ball shipped to 92563
Last edited by iownahatchback; 01-20-2010 at 07:37 PM.
#21
Honda-Tech Member
Thread Starter
Join Date: Feb 2005
Location: Arden, NC, USA
Posts: 758
Likes: 0
Received 0 Likes
on
0 Posts
Re: Turbo EG driveline partout
OP gauge sold sorry, I updated the post.
All the oil lines and fittings minus the manifolds - $20 plus shipping, West coast shipping runs 10-$15
All the oil lines and fittings minus the manifolds - $20 plus shipping, West coast shipping runs 10-$15
#22
Honda-Tech Member
Join Date: Sep 2007
Location: murrieta, ca, usa
Posts: 3,546
Likes: 0
Received 0 Likes
on
0 Posts