K-swap FMIC/CHARGEPIPING w/ Tial BOV flange and couplers/clamps CHEAP!!!!
#1
Member
Thread Starter
Join Date: Jun 2006
Location: s.shore, MA, USA
Posts: 1,781
Likes: 0
Received 0 Likes
on
0 Posts
K-swap FMIC/CHARGEPIPING w/ Tial BOV flange and couplers/clamps CHEAP!!!!
Alrighty guys, I'm looking to switch over to water to air for my intercooling setup so the FMIC/chargepiping setup I just built for my streetcar has to go. Here's some details...
-was fabbed for a sidewinder turbo kit in an EG (I can almost guarantee it will fit an ek/dc just fine)
-is all 2.5" mild steel mandrel bends, fabbed up by me.
-Pressure tested to 50psi no leaks
-tial BOV flange
-blue 4 ply reinforced silicone couplers included (1 for TB to chargepiping, 1 from turbo to chargepiping, and 2 for the FMIC in/out to chargepiping
-high quality tbolt clamps included
-intercooler was a REV-HARD fmic for an rsx-s kit, chopped and reworked for a split dual-inlet same side setup, 2.5" inlet/outlet, 3.0" thick core, about 7" high and 24" long. works nice, never had a problem with heatsoak on either of my kseries turbo setups... easily good for 400-450whp+++
-included brackets to mount the intercooler to stock EG crash bar mounts
Looking for $350 shipped, complete bolt-up setup OR BEST OFFER
I have many many many vouches on here, don't hesitate to make an offer! THANKS
-was fabbed for a sidewinder turbo kit in an EG (I can almost guarantee it will fit an ek/dc just fine)
-is all 2.5" mild steel mandrel bends, fabbed up by me.
-Pressure tested to 50psi no leaks
-tial BOV flange
-blue 4 ply reinforced silicone couplers included (1 for TB to chargepiping, 1 from turbo to chargepiping, and 2 for the FMIC in/out to chargepiping
-high quality tbolt clamps included
-intercooler was a REV-HARD fmic for an rsx-s kit, chopped and reworked for a split dual-inlet same side setup, 2.5" inlet/outlet, 3.0" thick core, about 7" high and 24" long. works nice, never had a problem with heatsoak on either of my kseries turbo setups... easily good for 400-450whp+++
-included brackets to mount the intercooler to stock EG crash bar mounts
Looking for $350 shipped, complete bolt-up setup OR BEST OFFER
I have many many many vouches on here, don't hesitate to make an offer! THANKS
#5
Member
Thread Starter
Join Date: Jun 2006
Location: s.shore, MA, USA
Posts: 1,781
Likes: 0
Received 0 Likes
on
0 Posts
Re: K-swap FMIC/CHARGEPIPING w/ Tial BOV flange and couplers/clamps CHEAP!!!!
thats how the intercooler came it doesnt look very birdshit to me buddy one end tank is cast and ones sheetmetal theres one bit of fiiller puddled up thats been ground away, I dont have the machine to work with aluminum as it is, I fabbed the chargepiping thats about it...
keep your scammer comments elsewhere, I have hundreds of vouches to back my dealings up, don't clutter my thread
keep your scammer comments elsewhere, I have hundreds of vouches to back my dealings up, don't clutter my thread
Thread
Thread Starter
Forum
Replies
Last Post
Javier
Southern California (Sales)
9
03-31-2010 09:11 AM
Javier
Northern California (Sales)
6
03-31-2010 09:09 AM
done
Classifieds: Forced Induction
10
05-21-2008 12:12 PM