Complete 800+WHP B-series motor for sale
#1
Honda-Tech Member
Thread Starter
Join Date: Dec 2004
Location: SomeWhere, Nj/Va, U.S.A
Posts: 274
Likes: 0
Received 0 Likes
on
0 Posts
Complete 800+WHP B-series motor for sale
I am selling a complete built 2.0 turbo motor. This motor has made over 800WHP on C-16 with a 71mm turbo.
AEBS 84mm sleeves
O-ringed
Race prepped LS crank
Pauter LS rods
Oem Honda Bearings throughout
84mm 9:1 Arias pistons
Upgraded thick wall wrist pins
New OEM Acura oil pump
New OEM Acura water pump
New OEM Acura T-belt
ATI SFI approved crank pulley
Fully race ported B-16 head
84mm combustion chambers
InlinePro springs and titanium retainers
Comp Cams custom turbo camshafts
ARP head studs
InlinePro sheet metal intake manifold port matched to head
RPM 74mm billet throttle body matched to intake
InlinePro fuel rail
1600cc injectors
This motor was completely refreshed 1 week ago and used for the last Import vs. Domestic race at MIR. Still in Mat Keller's T4 integra and can hear run. It also trapped 155+MPH with no second gear weighing 2450 lbs making 745WHP
Asking $7500.00 complete from throttle body to oil pan!!!
Can include NX direct port (never been sprayed) seen in picture for additional $700.00 This kit retails for $900.00 not including labor to bend lines and install in intake manifold.
This is less than it would cost for the parts in this motor not including any labor, machining costs, or the stock swap needed in order to have a motor sleeved snd head ported.
AEBS 84mm sleeves
O-ringed
Race prepped LS crank
Pauter LS rods
Oem Honda Bearings throughout
84mm 9:1 Arias pistons
Upgraded thick wall wrist pins
New OEM Acura oil pump
New OEM Acura water pump
New OEM Acura T-belt
ATI SFI approved crank pulley
Fully race ported B-16 head
84mm combustion chambers
InlinePro springs and titanium retainers
Comp Cams custom turbo camshafts
ARP head studs
InlinePro sheet metal intake manifold port matched to head
RPM 74mm billet throttle body matched to intake
InlinePro fuel rail
1600cc injectors
This motor was completely refreshed 1 week ago and used for the last Import vs. Domestic race at MIR. Still in Mat Keller's T4 integra and can hear run. It also trapped 155+MPH with no second gear weighing 2450 lbs making 745WHP
Asking $7500.00 complete from throttle body to oil pan!!!
Can include NX direct port (never been sprayed) seen in picture for additional $700.00 This kit retails for $900.00 not including labor to bend lines and install in intake manifold.
This is less than it would cost for the parts in this motor not including any labor, machining costs, or the stock swap needed in order to have a motor sleeved snd head ported.
#2
Honda-Tech Member
Thread Starter
Join Date: Dec 2004
Location: SomeWhere, Nj/Va, U.S.A
Posts: 274
Likes: 0
Received 0 Likes
on
0 Posts
Re: Complete 800+WHP B-series motor for sale (BryanD6200)
Mods...please move this to the race car/parts for sale thread...I don't even know how I ended up posting it in here?!?
Thread
Thread Starter
Forum
Replies
Last Post
Mr. Danieli
Classifieds: Forced Induction
19
11-28-2005 05:19 PM