mrbsponge

well i really got tired of running open downpipe, and smelling like raw *** gas when i got out of the car. plus it was mad loud, and i was always getting hassled by the local law.

so i grabbed some 3 inch mandrel bends from a buddy, got a stick of 3 inch from an exhaust shop, my chop saw and mig welder and went at it. not bad for my first complete exhaust, so i think.

i used a "Bullet" muffler from summit, the welds looked like ***, but for 27 bux i cant complain, i also used a 3 inch V band from full race to go from the downpipe to the exhaust, much easier to take off.

and i had to put a gangster dump on the back


V-BAND


MID-TO-REAR


OVER THE AXLE


other side


all in all i like it, i did have to put a couple tiny bends in it with a bender but nothing that would inhibit flow, it is much nicer to have the noise back at the rear of the car, instead of under my feet!

it is kinda loud still but i hadnt found a 3 inch resonator yet locally so i will probably have to order one from the internerD

180MPHGUY

do you have a flex section in your down pipe? if not your gonna break something some on your set up. other wise it look real good.

mrbsponge

o have a 6 or 8 inch flex in my downpipe, i utilized all the stock hangers with new rubber pieces as well to help give it some buffer room too.

thanks bro

LShatchie

looks really good, i am making a home made exhaust soon too

mrchaos

for an eg? what kind of bends did you end up using for around the corners and over the control arm?

LD_EGSICK

you should use a nother bullet muffler some where at the b pipe, it should make it alot quiter. but nice job i like the muffler tuck

mrbsponge

yeah im gonna have to do someting to quiet it down just a tad.

yes it is an EG, i used just your basic 90 degree bends, i think 3 of them, 1 for right in front of the gas tank, then 1 to make it go towards the back again, then i used one and cut it with my chop saw, to make it go over the control arm, i tucked it kinda high so i could put a Dump on it, gotta keep it gangsta' with the dump!

thanks for all the input guys, this exhaust literall cost me about 50 bux to make, i just had fun doin it

VRD^sam

looks nice...

infrontofu

Looks good Mike.... Function>Fashion...

mrbsponge

thanks chuck

damn i aint even in your vouches! thats messed up!

J/K

JCushing

hows that muffler sound? doenst look like theres much to it. you could reuse it as a resonator and get a bigger one in its place

mrbsponge

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by JCushing &raquo;</TD></TR><TR><TD CLASS="quote">hows that muffler sound? doenst look like theres much to it. you could reuse it as a resonator and get a bigger one in its place</TD></TR></TABLE>


thats my plan, but i needed something asap

infrontofu

What has it been 3 years since I talked to you?

added tho...

mrbsponge

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by infrontofu &raquo;</TD></TR><TR><TD CLASS="quote">What has it been 3 years since I talked to you?

added tho...</TD></TR></TABLE>

no ****** MAY of 2004 was the last time i saw your ***

0mtber

iTrader: (2)

Looks nice mike

allmotorsi04

once you end up in alabama it traps you and never lets you out.....haha j/k

VRD^don

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Dspec &raquo;</TD></TR><TR><TD CLASS="quote">looks nice... </TD></TR></TABLE>

baller

Mugencrxsir1

nice exhaust, but your still riding on arospeed sleeve coilovers?

mrbsponge

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Mugencrxsir1 &raquo;</TD></TR><TR><TD CLASS="quote">nice exhaust, but your still riding on arospeed sleeve coilovers?</TD></TR></TABLE>


i went 11.7 on spray with these coilovers, AND 11 flat turbo with these coilovers, i must be doin something right..........or they are good luck

infrontofu

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by mrbsponge &raquo;</TD></TR><TR><TD CLASS="quote">


i went 11.7 on spray with these coilovers, AND 11 flat turbo with these coilovers, i must be doin something right..........or they are good luck</TD></TR></TABLE>

Well put...

HamiltonRex

nice exhaust.

I just finsihed up my 3" stainless on my turbo crx.. but i had to have a cat.