Honda-Tech - Honda Forum Discussion

Notices
 
Page 1 of 2
1
2
Search: Posts Made By: hondacrx_gnvl
Showing results 1 to 25 of 29
Search took 0.33 seconds.
Forum: Tech / Misc
03-06-2012, 06:26 PM
Replies: 1
Views: 945
Posted By hondacrx_gnvl

Poor-Mans Type-R swap in 94 dx coupe Code9and 17

hey Guys,

Im just finished my Poor-mans type r swap.
B18c block 16 head.
dx harness and ex sub-harness(i believe)
The Car runs fine. but it still trow 2 Codes 9 and 17.
I try to get the car...
Forum: All Motor / Naturally Aspirated
09-16-2009, 01:57 PM
Replies: 16
Views: 978
Posted By hondacrx_gnvl

Re: After Rebuild Antifreez in the Oil.

na i will figure it out. I don't like to give up.
Forum: All Motor / Naturally Aspirated
09-14-2009, 07:30 PM
Replies: 16
Views: 978
Posted By hondacrx_gnvl

Re: After Rebuild Antifreez in the Oil.

yes i install 2 dowel pins.

thx torsten
Forum: All Motor / Naturally Aspirated
09-13-2009, 05:40 PM
Replies: 16
Views: 978
Posted By hondacrx_gnvl

Re: After Rebuild Antifreez in the Oil.

Hey

i just have the block back from the maschine Shop and the head . the motor and block is total Rebuilt. I never drove 1 mile with the car i just let car idel for but 30min. Can't drive the jet...
Forum: All Motor / Naturally Aspirated
09-13-2009, 03:50 PM
Replies: 16
Views: 978
Posted By hondacrx_gnvl

Re: After Rebuild Antifreez in the Oil.

i have to look to have a Diagram from the coolant lines.
1 line goes from the intake manifold to to evap and 1 line goes to radiator line.

THx torsten
Forum: All Motor / Naturally Aspirated
09-13-2009, 11:02 AM
Replies: 16
Views: 978
Posted By hondacrx_gnvl

Re: After Rebuild Antifreez in the Oil.

Hey Forum,

IM still have Antifreez in my Oil.
I replaced the Headgasket. How i can find out what the problem is.
I just let the car idel for about 45min the first 45min the oil is bin fine.
I...
Forum: All Motor / Naturally Aspirated
08-26-2009, 09:09 PM
Replies: 16
Views: 978
Posted By hondacrx_gnvl

Re: After Rebuild Antifreez in the Oil.

its a good question the head gasket only fit one way. how u know its the right way.

Thx torsten
Forum: All Motor / Naturally Aspirated
08-26-2009, 06:49 PM
Replies: 16
Views: 978
Posted By hondacrx_gnvl

Re: After Rebuild Antifreez in the Oil.

Thx i will dry this tomorov.

thx torsten
Forum: All Motor / Naturally Aspirated
08-26-2009, 05:19 PM
Replies: 16
Views: 978
Posted By hondacrx_gnvl

After Rebuild Antifreez in the Oil.

Hi All,

I just finish rebuild my Engine. D16A6
Arp head Stuts,
Eagle Rods,Vitara Piston.
T3/T4 trim Garrett.
I still have water in the Oil i Just replaced the the head gasket again.
I check...
Forum: Forced Induction
08-24-2009, 05:05 PM
Replies: 28
Views: 9,487
Posted By hondacrx_gnvl

Re: 1 Cylinder And 4 Cyliner 90 Psi Compression After Rebuild the Engine

I thing i find the problem. I thing its the camshaft. I will take the camshaft out and but the stock cam back in. and what the different is.

Thx guys for u help.

Thx torsten
Forum: Forced Induction
08-23-2009, 07:33 PM
Replies: 28
Views: 9,487
Posted By hondacrx_gnvl

Re: 1 Cylinder And 4 Cyliner 90 Psi Compression After Rebuild the Engine

take all 4 spark plugs out. then full throttle, crank the car. have no leak down tester.

Thx torsten
Forum: Forced Induction
08-23-2009, 07:01 PM
Replies: 28
Views: 9,487
Posted By hondacrx_gnvl

Re: 1 Cylinder And 4 Cyliner 90 Psi Compression After Rebuild the Engine

i mean cam cam pulley.
I did it the same way like u say. have a copy from the repair Manuel.
But its still not right.
No.1 piston 100psi No.2 piston 95psi No.3 Piston 130Psi No.4 85 psi.
I don't...
Forum: Forced Induction
08-23-2009, 04:06 PM
Replies: 28
Views: 9,487
Posted By hondacrx_gnvl

Re: 1 Cylinder And 4 Cyliner 90 Psi Compression After Rebuild the Engine

no water in the oil.

This is how i adjust Valves.

set no. 1 piston on TDC Up Mark on pulley on top.
TDC grooves on pulley align with cylinder head.
distributor roter point to No. 1....
Forum: Forced Induction
08-23-2009, 02:55 PM
Replies: 28
Views: 9,487
Posted By hondacrx_gnvl

Re: 1 Cylinder And 4 Cyliner 90 Psi Compression After Rebuild the Engine

Hey replaced the Head Gasket and check for any visible cracks in the head but looks fine.
I still have the low compression issue. the compression is 4 cylinder 96 1 cylinder 100.
Can some tell me...
Forum: Forced Induction
08-23-2009, 04:54 AM
Replies: 28
Views: 9,487
Posted By hondacrx_gnvl

Re: 1 Cylinder And 4 Cyliner 90 Psi Compression After Rebuild the Engine

My head and my block resurfaced. but i will u go and us same of the copper spray. the for the help.

torsten
Forum: Forced Induction
08-22-2009, 09:41 PM
Replies: 28
Views: 9,487
Posted By hondacrx_gnvl

Re: 1 Cylinder And 4 Cyliner 90 Psi Compression After Rebuild the Engine

Can i use the head gasket from auto zone or is better us a mls 75.5 Cometic gasket did the make any different.

Thx Torsten
Forum: Forced Induction
08-22-2009, 07:00 PM
Replies: 28
Views: 9,487
Posted By hondacrx_gnvl

Re: 1 Cylinder And 4 Cyliner 90 Psi Compression After Rebuild the Engine

I took of the head off and will replace the head gasket and will install the dowel pins thank for the help guys. i hope this will fix the problem.

Thx torsten
Forum: Forced Induction
08-22-2009, 05:14 PM
Replies: 28
Views: 9,487
Posted By hondacrx_gnvl

Re: 1 Cylinder And 4 Cyliner 90 Psi Compression After Rebuild the Engine

yes the the dowel pins for alighment. Well i thing i go oudside and start taking off the head again. Sound like i mist up big times.

Thx for the help guys.

Thx torsten

I someone from...
Forum: Forced Induction
08-22-2009, 04:52 PM
Replies: 28
Views: 9,487
Posted By hondacrx_gnvl

Re: 1 Cylinder And 4 Cyliner 90 Psi Compression After Rebuild the Engine

make sense. Well i guess i to pull of the Head again. To i have to use a new head gasket or can i use the old one.

Thx Torsten
Forum: Forced Induction
08-22-2009, 04:46 PM
Replies: 28
Views: 9,487
Posted By hondacrx_gnvl

Re: 1 Cylinder And 4 Cyliner 90 Psi Compression After Rebuild the Engine

yes my oil Looks like a milkshake. So do i have to pull of my head again.
I know i forget to install the dowel Pins can the be the problem.
OK will check this tomorrow.
Thx for the fast answer....
Forum: Forced Induction
08-22-2009, 04:25 PM
Replies: 28
Views: 9,487
Posted By hondacrx_gnvl

Re: 1 Cylinder And 4 Cyliner 90 Psi Compression After Rebuild the Engine

Can the Water be condensation. The Motor stay assembled but 7 weeks. i had to wait for my downpipe and manifold.
cU thing the water issue have something do to with the blockguard. (eagle...
Forum: Forced Induction
08-22-2009, 04:07 PM
Replies: 28
Views: 9,487
Posted By hondacrx_gnvl

Re: 1 Cylinder And 4 Cyliner 90 Psi Compression After Rebuild the Engine

Thx for the fast answer. Well thx u make my day sound not good at all.
Well the machine job check all thats stuff for me. but i thing i take the head off again. Is it Possible the The Timing...
Forum: Forced Induction
08-22-2009, 03:44 PM
Replies: 28
Views: 9,487
Posted By hondacrx_gnvl

1 Cylinder And 4 Cyliner 90 Psi Compression After Rebuild the Engine

Hey Forum,

I own i 89 Crx Si. D16A6.
I Finish to Rebuilt my Engine.
But now I'm running in some littel issues.
1 Issue: I done i Compression check 1 cylinder 93psi 2 Cylinder 120psi 3...
Forum: Honda CRX / EF Civic (1988 - 1991)
08-13-2009, 05:46 AM
Replies: 4
Views: 1,266
Posted By hondacrx_gnvl

Re: Wiring Problem,Starter, Lights,Signal Lights not working

thx for the answer. I try to start with a Battery booster it will not start. i took out the starter and took to advance the start is fine.

Thx Torsten :thud:
Showing results 1 to 25 of 29
 
Page 1 of 2
1
2


 
Forum Jump


All times are GMT -8. The time now is 08:33 PM.