Honda-Tech - Honda Forum Discussion

Notices
Search: Posts Made By: BuildOff
Showing results 1 to 21 of 21
Search took 0.33 seconds.
Forum: Welding / Fabrication
11-21-2008, 09:04 AM
Replies: 50
Views: 16,769
Posted By BuildOff

You're thinking inside the box. Remember, if...

You're thinking inside the box. Remember, if someone has the skill to make the block, the timing arrangement can be overcome. As stated, doing some work to drive the new cams off the opposite end...
Forum: All Motor / Naturally Aspirated
11-14-2008, 04:20 PM
Replies: 35
Views: 7,891
Posted By BuildOff

Great job Bisi!

In case anyone missed the Castrol Syntec Top Shop Challenge, the results are in this months magazines. Bisi built a 2.4L F22 SOHC, and scored a peak hp. of 360, and 239ft.lbs of torque. The...
Forum: Welding / Fabrication
11-14-2008, 02:31 PM
Replies: 50
Views: 16,769
Posted By BuildOff

Re: (Aquafina)

And why would one head need reversed rotation???
Forum: All Motor / Naturally Aspirated
11-12-2008, 06:47 PM
Replies: 29
Views: 17,431
Posted By BuildOff

Re: my valves wont seal no matter what... wtf?? (Combustion Contraption)

Also depends on the valveseat material. Ampco 45 and Berylium Copper definitely take a seating during the initial run-in. Ampco seats are really soft, but work harden on run-in. Berylium Copper...
Forum: All Motor / Naturally Aspirated
11-11-2008, 08:44 AM
Replies: 88
Views: 45,625
Posted By BuildOff

Re: 402 hp race K26 (crx=si)

Nalani has been running in the "9's" for a while!
Forum: All Motor / Naturally Aspirated
11-10-2008, 08:07 AM
Replies: 78
Views: 69,361
Posted By BuildOff

Re: My K20 rebuild (chunky)

In an attempt to decipher what the cause and effect were on your last build, can you show the back sides of the bearings, the con-ron/ cap parting surfaces, and the wristpin bore measurements...
Forum: All Motor / Naturally Aspirated
11-09-2008, 09:47 AM
Replies: 21
Views: 13,326
Posted By BuildOff

Re: (be18see1)

A good place to start is...

Take the rods to a decent machine shop with a new set of rod bolts. Have the machine shop resize the rods using the new rod bolts. Have the rods checked for twist,...
Forum: Drag Racing
11-06-2008, 09:38 PM
Replies: 1
Views: 1,085
Posted By BuildOff

Re: G Force or Xtrac? (Toyotakid714)

Scott,

Contact Jason Whitfield. I think he still has an X-Trac. Not sure how the gearing will work with your car though.
Forum: All Motor / Naturally Aspirated
11-04-2008, 05:33 PM
Replies: 34
Views: 1,815
Posted By BuildOff

Re: (edm_dc2)

If anyone has data that they would be willing to provide, but don't want on a public forum, I can be reached at brian_axup@yahoo.com.

Just as an informational help, of course I would like to see...
Forum: All Motor / Naturally Aspirated
11-04-2008, 11:55 AM
Replies: 34
Views: 1,815
Posted By BuildOff

Re: (Minor Threat)

Our competition will be similar to the Engine Masters Challenge.
Forum: All Motor / Naturally Aspirated
11-04-2008, 05:52 AM
Replies: 34
Views: 1,815
Posted By BuildOff

Re: (Natural Aspirations)

Very true! People are very secretive, especially if someone else could profit from their knowledge.

Here's a little preface of what I am upto:

I am working on assembling an engine building...
Forum: All Motor / Naturally Aspirated
11-03-2008, 09:24 PM
Replies: 34
Views: 1,815
Posted By BuildOff

Re: FV-QR (BuildOff)

Just found the WD-40 challenge that Honda Tuning Magazine organized a couple of years ago... Darren @ R&D Dyno had a pretty strong set-up

4000 109.3 143.5
4100 110.2 141.1...
Forum: All Motor / Naturally Aspirated
11-03-2008, 05:36 AM
Replies: 34
Views: 1,815
Posted By BuildOff

Re: FV-QR (projectTeG)

What are the details on the motor being dyno'ed in that screenshot?
Forum: All Motor / Naturally Aspirated
11-02-2008, 08:59 AM
Replies: 34
Views: 1,815
Posted By BuildOff

Re: Looking for detailed dyno info, not charts... (Natural Aspirations)

That is perfect! What were some of the specs on that engine? Bore, Stroke, Engine type, fuel used? https://honda-tech.com/forums/images/smilies/emthup.gif

By the way, that engine averaged...
Forum: All Motor / Naturally Aspirated
11-02-2008, 07:33 AM
Replies: 34
Views: 1,815
Posted By BuildOff

Re: (stealth50k)

Thanks, some of those have the type of info I am looking for. Not sure why Javier didn't start the pulls lower in the rev's, but it looks like he starts most runs between 5000 and 5500RPM. I need...
Forum: All Motor / Naturally Aspirated
11-01-2008, 04:45 PM
Replies: 34
Views: 1,815
Posted By BuildOff

Re: FV-QR (SMSP)

Dave,

Do you have the numeric data from the 84.5x89 build that you show on your website's dyno page?
Forum: All Motor / Naturally Aspirated
11-01-2008, 02:35 PM
Replies: 34
Views: 1,815
Posted By BuildOff

Re: FV-QR (DonF)

That screenshot has more info than I need. I'm just looking for hp. and tq. at each RPM point. 4000RPM to 8500RPM.

Oh, by the way, is that Depac software on a hand controlled dyno? Looks...
Forum: All Motor / Naturally Aspirated
11-01-2008, 08:30 AM
Replies: 34
Views: 1,815
Posted By BuildOff

Re: FV-QR (Combustion Contraption)

I understand that to some, their dyno info is private. That is one reason why I am looking for Hot Street type builds, not race builds.

Although it's not used widely, Dynojet gives you the...
Forum: All Motor / Naturally Aspirated
10-31-2008, 06:43 PM
Replies: 34
Views: 1,815
Posted By BuildOff

Re: Looking for detailed dyno info, not charts... (mar778c)

No, I can't accurately get the info from a graph. Most dyno programs offer you the option of a graphed output, or a numeric output. I need the numbers, not the lines of a graph......
Forum: All Motor / Naturally Aspirated
10-31-2008, 04:14 PM
Replies: 34
Views: 1,815
Posted By BuildOff

Looking for detailed dyno info, not charts...

I understand that there is a sticky with dyno charts that show various N/A setups, but none of them are detailed enough for what I need. I am looking for the numeric info that shows the hp/tq data...
Forum: All Motor / Naturally Aspirated
10-31-2008, 03:11 PM
Replies: 1
Views: 345
Posted By BuildOff

Need help finding detailed dyno runs for sub 2000cc. N/A builds

I am trying to research and compare various engine families. Can any of you direct me towards some detailed data from sub 2L N/A engines? What I'm looking for in particular are the hp/tq. readings...
Showing results 1 to 21 of 21


 
Forum Jump


All times are GMT -8. The time now is 07:38 AM.